Inspection and Verification
This section provides step-by-step module configuration procedures. Carry out the programmable module installation (PMI) procedure in this article when another workshop manual section directs to carry out configuration or when DTCs from the list below are present
| DTC | Description | Source | Action |
|---|---|---|---|
| B2477 | Module Configuration Failure | Audio control module (ACM) Audio digital signal processing (DSP) module Driver seat module (DSM) Dual climate control seat module (DCSM) Instrument cluster (IC) Occupant classification system module (OCSM) Parking aid module (PAM) Restraints control module (RCM) Satellite digital audio receiver system (SDARS) module Smart junction box (SJB) | CARRY OUT PMI. REFER to Programmable Module Installation in this article. |
| B2477 | Module Configuration Failure | Accessory protocol interface module (APIM) | REFER to Accessory Protocol Interface Module (APIM) Programming in this article. |
| B2900 | VIN mismatch | 4X4 control module ABS module RCM | CARRY OUT PMI. REFER to Programmable Module Installation in this article. |
| P0602 | Powertrain Control Module Programming Error | PCM | CARRY OUT PMI. REFER to Programmable Module Installation in this article. |
| P0605 | Internal Control Module Read Only Memory (ROM) Error | PCM | CARRY OUT PMI. REFER to Programmable Module Installation in this article. |
| P1635 | Tire/Axle Out of Acceptable Range | 4X4 control module | CARRY OUT PMI. REFER to Programmable Module Installation in this article. |
| P1639 | Vehicle ID Block Corrupted, Not Programmed | PCM | CARRY OUT PMI. REFER to Programmable Module Installation in this article. |
| U0300 | Internal Control Module Software Incompatibility | PCM RCM | CARRY OUT PMI. REFER to Programmable Module Installation in this article. |
| U2050 | No Application Present | 4X4 control module ABS module ACM DCSM DSM Driver door module (DDM) DSP module Heating ventilation air conditioning (HVAC) module IC OCSM PCM RCM SJB SDARS module Transmission control module (TCM) | CARRY OUT PMI. REFER to Programmable Module Installation in this article. |
| U2050 | No Application Present | APIM | REFER to Accessory Protocol Interface Module (APIM) Programming in this article. |
| U2051 | No Application Present | 4X4 control module ACM DSP module HVAC module IC OCSM PAM PCM RCM | CARRY OUT PMI. REFER to Programmable Module Installation in this article. |
DTC CHART
Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is Available
Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the specific module removal and installation procedures.
- Connect the IDS and identify the vehicle as normal.
- From the Tool box icon, select Module Programming and press the check mark.
- Select Programmable Module Installation.
- Select the module that is being replaced.
- Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
- Install the new module and press the check mark.
- Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
- The IDS downloads the data into the new module and displays Module Configuration Complete.
- Test module for correct operation.
Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is NOT Available
Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the specific module removal and installation procedures.
- Install the new module.
- Connect the IDS and identify the vehicle as normal.
- From the Tool box icon, select Module Programming and press the check mark.
- Select Programmable Module Installation.
- Select the module that was replaced.
- Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
- Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
- If the data is not available, the IDS displays a screen stating to contact the As-Built Data Center. Retrieve the data from the technician service publication website at this time and press the check mark.
- Enter the module data and press the check mark.
- The IDS downloads the data into the new module and displays Module Configuration Complete.
- Test module for correct operation.
Accessory Protocol Interface Module (APIM) Programming Using the Integrated Diagnostic System (IDS)
Note. If a new accessory protocol interface module (APIM) is being installed, install the new APIM before carrying out the following procedure. For additional information, refer to INFORMATION AND ENTERTAINMENT SYSTEMS article.
- Turn the audio control module (ACM) on.
- Connect the scan tool to the data link connector (DLC).
- Connect one end of the universal serial bus (USB) male-A to male-A cable to the scan tool.
- Connect the other end of the USB male-A to male-A cable to the vehicle USB port.
- From the technician service publication website, run OASIS using Quick Start or by manually entering the vehicle identification number (VIN).
- From the OASIS tab, select the "Sync/APIM" bullet.
- Select the "Read APIM" button to verify the current APIM vehicle interface processor (VIP) and consumer interface processor (CIP) software levels.
- Select the desired software level from the list of available software for programming then select the "Program APIM" button to begin the APIM programming process. Enter the APIM As-Built data if prompted. When only the CIP is being programmed, select cancel when prompted whether or not to program the VIP. When the VIP is programmed, the CIP will be programmed automatically.
- The Sync/APIM application downloads the software into the APIM and displays "Programming has been completed successfully".
- Test the audio system for correct operation.