Inspection and Verification
This article provides step-by-step module configuration procedures. Carry out Programmable Module Installation (PMI) procedures when another article directs to carry out configuration or when DTCs from the below list are present
| DTC | Description | Source | Action |
|---|---|---|---|
| B2477 | Module Configuration Failure | Audio control module (ACM) Front display interface module (FDIM) Instrument cluster (IC) Satellite digital audio receiver system (SDARS) module Smart junction box (SJB) | CARRY OUT PMI. REFER to Programmable Module Installation (PMI) . |
| B2477 | Module Configuration Failure | Accessory protocol interface module (APIM) | REFER to Accessory Protocol Interface Module (APIM) Programming . |
| B2477 | Module Configuration Failure | Heating ventilation air conditioning (HVAC) module | INSTALL a new HVAC module. REFER to CLIMATE CONTROL . |
| B2477 | Module Configuration Failure | Restraints control module (RCM) | INSTALL a new RCM. REFER to SUPPLEMENTAL RESTRAINT SYSTEM . |
| P0602 | Powertrain Control Module Programming Error | PCM | CARRY OUT PMI. REFER to Programmable Module Installation (PMI) . |
| P0605 | Internal Control Module Read Only Memory (ROM) Error | PCM | CARRY OUT PMI. REFER to Programmable Module Installation (PMI) . |
| P1639 | Vehicle ID Block Corrupted, Not Programmed | PCM | CARRY OUT PMI. REFER to Programmable Module Installation (PMI) . |
| U0300 | Internal Control Module Software Incompatibility | PCM | CARRY OUT PMI. REFER to Programmable Module Installation (PMI) . |
| U0300 | Internal Control Module Software Incompatibility | HVAC module | INSTALL a new HVAC module. REFER to CLIMATE CONTROL . |
| U2050 | No Application Present | ACM FDIM IC PCM SDARS module SJB | CARRY OUT PMI. REFER to Programmable Module Installation (PMI) . |
| U2050 | No Application Present | ABS module | INSTALL a new ABS module. REFER to VEHICLE DYNAMIC SYSTEMS . |
| U2050 | No Application Present | APIM | REFER to Accessory Protocol Interface Module (APIM) Programming . |
| U2050 | No Application Present | HVAC module | INSTALL a new HVAC module. REFER to CLIMATE CONTROL . |
| U2050 | No Application Present | Front controls interface module (FCIM) | INSTALL a new FCIM. REFER to INFORMATION AND ENTERTAINMENT SYSTEMS . |
| U2050 | No Application Present | Occupant classification system module (OCSM) | INSTALL a new OCSM. REFER to SUPPLEMENTAL RESTRAINT SYSTEM . |
| U2050 | No Application Present | RCM | INSTALL a new RCM. REFER to SUPPLEMENTAL RESTRAINT SYSTEM . |
| U2051 | One or More Calibration Files Missing / Corrupt | ACM FDIM PCM | CARRY OUT PMI. REFER to Programmable Module Installation (PMI) . |
| U2051 | One or More Calibration Files Missing / Corrupt | FCIM | INSTALL a new FCIM. REFER to INFORMATION AND ENTERTAINMENT SYSTEMS . |
| U2051 | One or More Calibration Files Missing / Corrupt | HVAC module | INSTALL a new HVAC module. REFER to CLIMATE CONTROL . |
| U2051 | One or More Calibration Files Missing / Corrupt | OCSM | INSTALL a new OCSM. REFER to SUPPLEMENTAL RESTRAINT SYSTEM . |
| U2051 | One or More Calibration Files Missing / Corrupt | RCM | INSTALL a new RCM. REFER to SUPPLEMENTAL RESTRAINT SYSTEM . |
DTC CHART
Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is Available
Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the appropriate article for module removal and installation procedures for the specific module(s).
- Connect the IDS and identify the vehicle as normal.
- From the Toolbox icon, select Module Programming and press the check mark.
- Select Programmable Module Installation.
- Select the module that is being replaced.
- Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
- Install the new module and press the check mark.
- Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
- The IDS downloads the data into the new module and displays Module Configuration Complete.
- Test module for correct operation.
Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is NOT Available
Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the appropriate article for module removal and installation procedures for the specific module(s).
- Install the new module.
- Connect the IDS and identify the vehicle as normal.
- From the Toolbox icon, select Module Programming and press the check mark.
- Select Programmable Module Installation.
- Select the module that was replaced.
- Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
- Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
- If the data is not available, the IDS displays a screen stating to contact the As-Built Data Center. Retrieve the data from the technician service publication website at this time and press the check mark.
- Enter the module data and press the check mark.
- The IDS downloads the data into the new module and displays Module Configuration Complete.
- Test module for correct operation.
Accessory Protocol Interface Module (APIM) Programming Using the Integrated Diagnostic System (IDS)
Note. If a new accessory protocol interface module (APIM) is being installed, install the new APIM before carrying out the following procedure. For additional information, refer to INFORMATION AND ENTERTAINMENT SYSTEMS .
- Turn the audio control module (ACM) on.
- Connect the scan tool to the data link connector (DLC).
- Connect one end of the universal serial bus (USB) male-A to male-A cable to the scan tool.
- Connect the other end of the USB male-A to male-A cable to the vehicle USB port.
- From the technician service publication website, run OASIS using Quick Start or by manually entering the vehicle identification number (VIN).
- From the OASIS tab, select the "Sync/APIM" bullet.
- Select the "Read APIM" button to verify the current APIM vehicle interface processor (VIP) and consumer interface processor (CIP) software levels.
- Select the desired software level from the list of available software for programming then select the "Program APIM" button to begin the APIM programming process. Enter the APIM As-Built data if prompted. When only the CIP is being programmed, select cancel when prompted whether or not to program the VIP. When the VIP is programmed, the CIP will be programmed automatically.
- The Sync/APIM application downloads the software into the APIM and displays "Programming has been completed successfully".
- Test the audio system for correct operation.