Contents Wiring diagrams Section: Engine -- 2.0L Spi All sections

Material Ford Focus I facelift

Engine -- 2.0L Spi ~1330 words

Material

ItemSpecification
Engine oilWSS-M2C153-H

MATERIAL SPECIFICATIONS

Scheme 721

Scheme 721: Removal

Scheme 722

Scheme 722
  1. Remove the timing belt. For additional information, refer to TIMING BELT .
  2. Using the special tools, support the engine.
  3. Remove the jack.
  4. Raise and support the vehicle. For additional information, refer to JACKING AND LIFTING .
  5. Remove the crankshaft timing belt pulley.
  6. Using the special tool, remove and discard the crankshaft front oil seal.

Scheme 723

Scheme 723: Installation

Scheme 724

Scheme 724

Scheme 725

Scheme 725
  1. Using the special tool, install a new crankshaft oil seal. Lubricate the crankshaft and crankshaft oil seal lip with engine oil.
  2. Install the crankshaft timing belt pulley.
  3. Lower the vehicle.
  4. Place the jack under the oil pan and raise slowly until the special tool 303-290 is free from strain.
  5. Remove the special tools.
  6. Install the timing belt. For additional information, refer to TIMING BELT .
ItemSpecification
Cable ties
Silicone greaseA969-M1C17-AA

SPECIAL TOOL SPECIFICATIONS

Scheme 726

Scheme 726: Removal

Scheme 727

Scheme 727
  1. Disconnect the battery ground cable. For additional information, refer to BATTERY, MOUNTING AND CABLES .
  2. Disconnect the ignition wires from the spark plugs. Remove the two ignition wire separators from the valve cover.
  3. Remove the spark plugs.
  4. Remove the valve cover.
  5. Remove the rocker arms.
  6. Install an adaptor and apply 965 kPa of air pressure to hold the valve shut.
  7. Using the special tool to compress the valve spring and remove the valve spring retainer key and the valve spring.

Scheme 728

Scheme 728: Installation

Scheme 729

Scheme 729

Scheme 730

Scheme 730

Scheme 731

Scheme 731
  1. Use the special tool to compress the valve spring and install the valve spring retainer.
  2. Install the rocker arms.
  3. Remove the adaptor.
  4. Install the valve cover.
  5. Install the spark plugs (shown with engine removed). Apply lubricant to the spark plug thread.
  6. Push on the spark plug connector until it engages.
  7. Connect the battery ground cable. For additional information, refer to BATTERY, MOUNTING AND CABLES .

Scheme 732

Scheme 732: Removal
  1. Remove the valve springs. For additional information, refer to VALVE SPRINGS .
  2. Remove and discard the valve stem seal.

Scheme 733

Scheme 733: Installation
  1. Install the valve stem seal.
  2. Install the valve springs. For additional information, refer to VALVE SPRINGS .
ItemSpecification
Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil XO-5W20-QSP (in Canada Motorcraft SAE 5W-20 Super Premium Motor Oil CXO-5W20-LSP12) or equivalentWSS-M2C930-A

MATERIAL SPECIFICATIONS

Scheme 734

Scheme 734: Removal

Scheme 735

Scheme 735

Scheme 736

Scheme 736

Scheme 737

Scheme 737

Scheme 738

Scheme 738

Scheme 739

Scheme 739

Scheme 740

Scheme 740

Scheme 741

Scheme 741

Scheme 742

Scheme 742

Scheme 743

Scheme 743

Scheme 744

Scheme 744

Scheme 745

Scheme 745

Scheme 746

Scheme 746
  1. Remove the battery. For additional information, refer to BATTERY, MOUNTING AND CABLES .
  2. Remove the battery tray and detach the ground cable. Unclip and disconnect the electrical connector. Unclip the wiring harness. Remove the bolts. Detach the positive and negative cables.
  3. Remove the air cleaner housing. Disconnect the mass air flow (MAF) sensor electrical connector. Detach the air cleaner outlet pipe. Remove the air cleaner housing from the rubber bushing.
  4. Remove the air cleaner intake pipe.
  5. Remove the electrical ignition (El) coil. Disconnect the electrical connector. Remove the bolts and position the El coil.
  6. Disconnect the fresh air and positive crankcase ventilation hoses.
  7. Remove the valve cover.
  8. Remove the rocker arms.
  9. Remove the valve tappets. Remove the valve tappet guide plate retainers. Remove the valve tappet guide plates. Remove the valve tappets.
  10. Remove the timing belt. For additional information, refer to TIMING BELT .
  11. Remove the camshaft oil seal. For additional information, refer to CAMSHAFT SEAL .
  12. Using the special tools, support the engine.
  13. Remove the engine rear mounting.
  14. Detach the air cleaner housing bracket and position it to one side.
  15. Remove the camshaft thrust plate.
  16. Remove and discard the blanking plug from the rear of the cylinder head.
  17. Remove the camshaft from the rear of the cylinder head.

Scheme 747

Scheme 747: Installation

Scheme 748

Scheme 748

Scheme 749

Scheme 749

Scheme 750

Scheme 750

Scheme 751

Scheme 751

Scheme 752

Scheme 752

Scheme 753

Scheme 753

Scheme 754

Scheme 754

Scheme 755

Scheme 755

Scheme 756

Scheme 756

Scheme 757

Scheme 757

Scheme 758

Scheme 758
  1. Install the camshaft through the rear of the cylinder head.
  2. Install the camshaft thrust plate.
  3. Install a new camshaft oil seal. For additional information, refer to CAMSHAFT SEAL .
  4. Install a new blanking plug with sealer.
  5. Attach the air cleaner housing bracket.
  6. Install the engine rear mounting.
  7. Lower the engine.
  8. Remove the special tools.
  9. Install the timing belt. For additional information, refer to TIMING BELT .
  10. Install the valve tappets into the cylinder head bores with the oil feed holes (1) in the valve tappets facing away from the oil feed holes (2) in the cylinder head bores.
  11. Install the valve tappet guide plates (1) and valve tappet guide retainers (2).
  12. Install the rocker arms.
  13. Install the valve cover.
  14. Connect the fresh air and positive crankcase ventilation hoses. Make sure that the positive crankcase ventilation hose is secured.
  15. Install the El coil. Connect the electrical connector. Install the bolts.
  16. Install the air cleaner intake pipe.
  17. Install the air cleaner housing. Connect the MAF electrical connector. Attach the air cleaner intake pipe. Push the air cleaner housing into the rubber bushing.
  18. Install the battery tray. Install the positive and negative cables. Tighten the bolts. Clip on the wiring harness. Connect and attach the electrical connector.
  19. Install the battery. For additional information, refer to BATTERY, MOUNTING AND CABLES .
ItemSpecification
Engine oilWSS-M2C153-H

MATERIAL SPECIFICATIONS

Scheme 759

Scheme 759: Removal

Scheme 760

Scheme 760
  1. Remove the timing belt. For additional information, refer to TIMING BELT .
  2. Using the special tool, remove the camshaft timing belt pulley.
  3. Using the special tool, remove the camshaft oil seal.

Scheme 761

Scheme 761: Installation

Scheme 762

Scheme 762
  1. Using the special tool, install a new oil seal. Lubricate the oil seal lip and the camshaft running face with engine oil. Insert the oil seal in the special tool and draw it in with the timing belt pulley bolt.
  2. Using the special tool, install the camshaft timing belt pulley.
  3. Install the timing belt. For additional information, refer to TIMING BELT .
ItemSpecification
Cable ties
Silicon greaseA969-M1C171-AA

MATERIAL SPECIFICATIONS

Scheme 763

Scheme 763: Removal

Scheme 764

Scheme 764

Scheme 765

Scheme 765

Scheme 766

Scheme 766

Scheme 767

Scheme 767

Scheme 768

Scheme 768

Scheme 769

Scheme 769

Scheme 770

Scheme 770
  1. Remove the accessory drive belt.
  2. Detach the coolant expansion tank. Remove the bolt and position the expansion tank to one side.
  3. Detach the power steering reservoir and position to one side.
  4. Remove the right-hand front wheel and tire. For additional information, refer to WHEELS AND TIRES .
  5. Remove the crankshaft pulley/vibration damper.
  6. Lower the vehicle.
  7. Disconnect the ignition wires from the spark plugs. Remove the two ignition wire separators from the valve cover.
  8. Remove the spark plugs (shown with engine removed).
  9. Place a jack with a wooden block under the oil pan and raise slowly until the front engine mounting is free from strain.
  10. Remove the engine front mounting.
  11. Remove the timing belt cover.
  12. Remove the engine front mounting bracket (shown with engine removed).
  13. Align the timing marks.
  14. Remove the timing belt. Use an 8 mm Allen wrench and turn counter clockwise 1/4 turn. Insert a 3 mm (1/8 inch) drill bit to lock the timing belt tensioner in place. Remove the timing belt.

Scheme 771

Scheme 771: Installation

Scheme 772

Scheme 772

Scheme 773

Scheme 773

Scheme 774

Scheme 774

Scheme 775

Scheme 775

Scheme 776

Scheme 776

Scheme 777

Scheme 777

Scheme 778

Scheme 778

Scheme 779

Scheme 779

Scheme 780

Scheme 780
  1. Check the alignment of the timing mark on the crankshaft timing belt pulley.
  2. Check the alignment of the timing mark on the camshaft timing belt pulley.
  3. Install the timing belt. Install the timing belt over the pulleys in a counter clockwise direction starting at the crankshaft. Keep the belt span from the crankshaft to the camshaft tight while installing the timing belt over the camshaft. Remove the 3 mm (1/8 inch) drill bit to release the timing belt tensioner.
  4. Turn the crankshaft at least two turns in clockwise direction to TDC position for cylinder one.
  5. Check the alignment of the timing marks. If the alignment is not correct repeat the previous steps.
  6. Install the engine front mounting bracket (shown with engine removed).
  7. Install the timing belt cover (shown with engine removed).
  8. Install the engine front mounting.
  9. Remove the jack.
  10. Install the spark plugs (shown with engine removed).
  11. Push on the spark plug connector until it engages.
  12. Raise and support the vehicle. For additional information, refer to JACKING AND LIFTING .
  13. Install the crankshaft pulley/vibration damper. Position the drive belt on the crankshaft pulley.
  14. Install the right-hand front wheel and tire. For additional information, refer to WHEELS AND TIRES .
  15. Install the power steering reservoir.
  16. Install the coolant expansion tank.
  17. Install the accessory drive belt.