Home ReviewsRefund
Home/Ford/Explorer/Ford Explorer IV (2005-2010)/Repair manual/Communication Devices/Module Configuration: Diagnosis
Contents Wiring diagrams Section: Communication Devices All sections

Module Configuration: Diagnosis Ford Explorer IV

Communication Devices ~360 words

Inspection and Verification

This section provides step-by-step module configuration procedures. Carry out the Programmable Module Installation when another workshop manual section directs to carry out configuration or when DTCs from the below list are present

DTCDescriptionSourceAction
B2477Module Configuration FailureAnti-lock brake system (ABS) module Audio unit Driver seat module (DSM) Digital versatile disc (DVD) player Electronic automatic temperature control (EATC) Parking aid module (Mountaineer, Explorer Sport Trac) Instrument cluster Restraints control module (RCM) Satellite radio receiver Smart junction box (SJB)CARRY OUT PMI. REFER to Programmable Module Installation .
B2477Module Configuration FailureOccupant classification sensor moduleINSTALL a new occupant classification sensor module. REFER to SUPPLEMENTAL RESTRAINT SYSTEM .
B2900VIN mismatchABS module RCMCARRY OUT PMI. REFER to Programmable Module Installation .
P0602Powertrain Control Module Programming ErrorPowertrain control module (PCM)CARRY OUT PMI. REFER to Programmable Module Installation .
P0605Internal Control Module Read Only Memory (ROM) ErrorPCMCARRY OUT PMI. REFER to Programmable Module Installation .
P0605Internal Control Module Read Only Memory (ROM) ErrorTransmission control module (TCM)INSTALL a new TCM. REFER to AUTOMATIC TRANSAXLE/TRANSMISSION - 6R60 .
P1639Vehicle ID Block Corrupted, Not ProgrammedPCMCARRY OUT PMI. REFER to Programmable Module Installation .
U0300Internal Module Software IncompatibilityRCMCARRY OUT PMI. REFER to Programmable Module Installation .
U2050No Application PresentABS module Audio unit Driver seat module DVD player EATC Four wheel drive (4WD) control module Instrument cluster Power running board module RCM Satellite radio receiver SJBCARRY OUT PMI. REFER to Programmable Module Installation .
U2050No Application PresentOccupant classification sensor moduleINSTALL a new occupant classification sensor module. REFER to SUPPLEMENTAL RESTRAINT SYSTEM .
U2051One or More Calibration Files Missing / CorruptAudio unit EATC Instrument cluster RCMCARRY OUT PMI. REFER to Programmable Module Installation .
U2051One or More Calibration Files Missing / CorruptOccupant classification sensor moduleINSTALL a new occupant classification sensor module. REFER to SUPPLEMENTAL RESTRAINT SYSTEM .
U2051One or More Calibration Files Missing / CorruptParking aid module (PAM)INSTALL a new parking aid module. REFER to PARKING AID .

DIAGNOSTIC TROUBLE CODE (DTC) CHART

Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is Available

Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the specific module removal and installation procedures.

  1. Connect the IDS and identify the vehicle as normal.
  2. From the Toolbox icon, select Module Programming and press the check mark.
  3. Select Programmable Module Installation.
  4. Select the module that is being replaced.
  5. Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
  6. Install the new module and press the check mark.
  7. Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
  8. The IDS downloads the data into the new module and displays Module Configuration Complete.
  9. Test module for correct operation.

Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is NOT Available

Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the specific module removal and installation procedures.

  1. Install the new module.
  2. Connect the IDS and identify the vehicle as normal.
  3. From the Toolbox icon, select Module Programming and press the check mark.
  4. Select Programmable Module Installation.
  5. Select the module that was replaced.
  6. Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
  7. Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
  8. If the data is not available, the IDS displays a screen stating to contact the As-Built Data Center. Retrieve the data from the technician service publication website at this time and press the check mark.
  9. Enter the module data and press the check mark.
  10. The IDS downloads the data into the new module and displays Module Configuration Complete.
  11. Test module for correct operation.

More articles — Module Configuration