ALIGNMENT SPECIFICATIONS
| Item | LH | RH | Total/Split |
|---|---|---|---|
| E-150 | |||
| Caster | 4.0° +/- 2.75° | 4.5° +/- 2.75° | 0.5° +/- 1.0° |
| Camber | 0.25° +/- 0 5° | 0.25° +/- 0 5° | 0° +/- 0.5° |
| Toe (Positive value is toe-in, negative value is toe-out) | 0.06° +/- 0.25° | ||
| E-250 and E-350 | |||
| Caster | 4.0° +/- 2.75° | 4.5° +/- 2.75° | 0.5° +/- 1.0° |
| Camber | 0.5° +/- 0.5° | 0.5° +/- 0.5° | 0° +/- 0.5° |
| Toe (Positive value is toe-in, negative value is toe-out) | 0.06° +/- 0.25° | ||
| E-Super Duty | |||
| Caster | 4.0° +/- 2.75° | 4.5° +/- 2.75° | 0.5° +/- 1.0° |
| Camber | 0.5° +/- 0.5° | 0.5° +/- 0.5° | 0° +/- 0.5° |
| Toe (Positive value is toe-in, negative value is toe-out) | 0.06° +/- 0.25° | ||
ALIGNMENT SPECIFICATIONS
GENERAL SPECIFICATIONS
| Item | Specification |
|---|---|
| Dogtracking - maximum (centerline of front tires compared to centerline of rear tires) | 30 mm (1.25 in.) |
| Clear Vision | |
| Clear vision (negative value is counterclockwise) | 0° +/- 3° |
| Ball Joint Deflection | |
| Lower | 0-1.0 mm (0-0.040 in.) |
| Upper | 0-0.6 mm (0-0.024 in.) |
| Vehicle Lean (Side-to-Side Height Differences) | |
| Front wheel opening - maximum | 15 mm (5/8 in.) |
| Rear wheel opening - maximum | 20 mm (3/4 in.) |
GENERAL SPECIFICATIONS
CAMBER/CASTER SERVICE ADJUSTER SPECIFICATIONS
| Service Adjuster Type (Degrees) | Position Slot in Axle (Degrees) | LH Axle | RH Axle | ||
|---|---|---|---|---|---|
| Camber Change (Degrees) | Caster Change (Degrees) | Camber Change (Degrees) | Caster Change (Degrees) | ||
| 1/2 | 0 | 0.5 | 0 | +0.5 | 0 |
| 1 | 0 | 1.0 | 0 | +1.0 | 0 |
| 1-1/2 | 0 | 1.5 | 0 | +1.5 | 0 |
| 1/2 | 45 | 0.25 | +0.25 | +0.25 | +0.25 |
| 1 | 45 | 0.75 | +0.75 | +0.75 | +0.75 |
| 1-1/2 | 45 | 1.0 | +1.0 | +1.0 | +1.0 |
| 1/2 | 90 | 0 | +0.5 | 0 | +0.5 |
| 1 | 90 | 0 | +1.0 | 0 | +1.0 |
| 1-1/2 | 90 | 0 | +1.5 | 0 | +1.5 |
| 1/2 | 135 | +0.25 | +0.25 | 0.25 | +0.25 |
| 1 | 135 | +0.75 | +0.75 | 0.75 | +0.75 |
| 1-1/2 | 135 | +1.0 | +1.0 | 1.0 | +1.0 |
| 1/2 | 180 | +0.5 | 0 | 0.5 | 0 |
| 1 | 180 | +1.0 | 0 | 1.0 | 0 |
| 1-1/2 | 180 | +1.5 | 0 | 1.5 | 0 |
| 1/2 | 225 | +0.25 | 0.25 | 0.25 | 0.25 |
| 1 | 225 | +0.75 | 0.75 | 0.75 | 0.75 |
| 1-1/2 | 225 | +1.0 | 1.0 | 1.0 | 1.0 |
| 1/2 | 270 | 0 | 0.5 | 0 | 0.5 |
| 1 | 270 | 0 | +1.0 | 0 | 1.0 |
| 1-1/2 | 270 | 0 | 1.5 | 0 | 1.5 |
| 1/2 | 315 | 0.25 | 0.25 | +0.25 | 0.25 |
| 1 | 315 | 0.75 | 0.75 | +0.75 | 0.75 |
| 1-1/2 | 315 | 1.0 | 1.0 | + 1.0 | 1.0 |
CAMBER/CASTER SERVICE ADJUSTER SPECIFICATIONS
TORQUE SPECIFICATIONS
| Description | Nm |
|---|---|
| Pinch bolt at upper ball joint | 87-119 |
| Adjusting sleeve nuts and bolts | 49 |
TORQUE SPECIFICATIONS
See also:
• JACKING & LIFTING