Home ReviewsRefund
Home/Ford/C-MAX/Ford C-MAX II (2010-2015)/Repair manual/Cruise Control Systems/Multifunction Electronic Modules: Removal & Installation
Contents Wiring diagrams Section: Cruise Control Systems All sections

Multifunction Electronic Modules: Removal & Installation Ford C-MAX II

Cruise Control Systems ~1093 words

Removal

Note. Removal steps in this procedure may contain installation details.

Pinpoint Test B

B2 BCM
  1. NOTE: If installing a new BCM , verify at least 2 of the vehicle keys are available prior to carrying out this procedure.
  2. NOTE: If installing a new module, it is necessary to upload the module configuration information to the scan tool prior to removing the module. This information must be downloaded into the new module after installation.
  3. Upload the module configuration information from the BCM into the scan tool by following the scan tool on-screen instructions. For additional information
  4. Refer to: «MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION»(ref-635227-S01000970482014070200000) .
B7 BCM
  1. click to open the image

Installation

Pinpoint Test B

B1 BCM
  1. NOTE: The BCM still communicates with the scan tool with the ignition off. Use the previous scan tool session or start a scan tool session using the PCM part number or tear tag number located on the PCM . The tear tag can be found by double-clicking the VIN in the top left corner of PTS after OASIS has been ran for the VIN .
  2. NOTE: Low vehicle battery state of charge can affect proper module programming. Battery state of charge can be monitored on the scan tool. A red battery icon would indicate low vehicle battery state of charge. Over voltage may also affect module programming.
  3. NOTE: Make sure the battery is fully charged before starting the installation procedure. Do not have a battery charger connected to the vehicle charging system during the installation procedure.
  4. NOTE: Carry out Steps 2-16 only if installing a new BCM .
  5. To install, reverse the removal procedure.
B2 PMI
B5 OASIS
  1. NOTE: If a diagnostic scan tool is connected to the Internet, it will automatically obtain As-Built data. If a diagnostic scan tool is not connected to the Internet, obtain the As-Built data from Professional Technician Society (PTS) OASIS . Download the As-Built data to the scan tool or other storage device, such as a flash drive, following the on-screen instructions.
  2. From the Car Configuration screen select "Retrieve PTS derived ASBUILT data". Follow the on-screen instructions to install the as-built data into the BCM .
  3. click to open the image
B8 PATS
  1. NOTE: Due to Intelligent Access (IA), key transponder internal location, proper key orientation is required for successful key programming. Transponder location is on right side of steering column.
  2. Turn ignition on. On vehicles with IA, place the IA key in the PATS transceiver slot.
  3. click to open the image
B10 PCM
  1. NOTE: If a tear tag or PCM part number was used to establish the scan tool session, it may be necessary to now establish a new session using the normal process.
  2. Using a scan tool, enter the PATS Functions and follow the on-screen instructions to enter PATS security access.
B11 BCM
B12 PATS
  1. NOTE: PATS security access may need to be granted again.
  2. Select parameter reset BCM and PCM . Follow the on-screen instructions.
B16 BCM
B17 PCM
  1. NOTE: This step only applies to C-MAX Energi.
  2. Perform a PCM Keep Alive Memory (KAM) reset by following the scan tool on screen instructions.

Note. Removal steps in this procedure may contain installation details.

Pinpoint Test B

B2 RFA
  1. NOTE: If installing a new RFA module, verify at least 2 of the vehicle keys are available prior to carrying out this procedure.
  2. NOTE: If installing a new module, it is necessary to upload the module configuration information to the scan tool prior to removing the module. This information must be downloaded into the new module after installation.
  3. Upload the module configuration information from the RFA module into the scan tool by following the scan tool on screen instructions.
B3 LH
  1. Refer to: «LOADSPACE TRIM PANEL LH»(ref-635245-S31821996522014070200000) .
B4 RFA
  1. click to open the image

Pinpoint Test B

B1 RFA
  1. NOTE: If installing a new RFA module, do not turn on the ignition until a parameter reset is performed and 2 keys are programmed to the vehicle. The RFA module still communicates with the scan tool with the ignition off. Use the previous scan tool session or start a scan tool session using the PCM part number or tear tag.
  2. Install the 5 electrical connectors, and the RFA module.
  3. Torque: 89 lb.in (10 Nm)
  4. click to open the image
B2 LH
  1. Refer to: «LOADSPACE TRIM PANEL LH»(ref-635245-S31821996522014070200000) .
B3 RFA
  1. Refer to: «PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET»(ref-635240-S39090376022014070200000) .
  2. Refer to: «PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET»(ref-635243-S12900312582014070200000) .
B4 RFA
  1. Refer to: «KEY PROGRAMMING USING DIAGNOSTIC EQUIPMENT»(ref-635240-S26247227762014070200000) .
  2. Refer to: «KEY PROGRAMMING USING DIAGNOSTIC EQUIPMENT»(ref-635240-S26247227762014070200000) .
B5 RFA
B6 RFA

Note. Removal steps in this procedure may contain installation details.

Pinpoint Test B

B1 Front Door Module
  1. WARNING: Before beginning any service procedure in this article, refer to Safety Warnings in «GENERAL INFORMATION»(ref-635189) . Failure to follow this instruction may result in serious personal injury.
  2. Refer to: «HEALTH AND SAFETY PRECAUTIONS»(ref-635189-S18367805802014070200000) .
  3. Front Door Module
B4 Rear Door Module
  1. click to open the image
  2. Rear Door Module
  1. To install, reverse the removal procedure.

More articles — Multifunction Electronic Modules