Repair manual
Dodge Shadow I Repair Manual
Step-by-step repair and maintenance instructions for the Dodge Shadow I (1986–1994): removal, installation, adjustment, diagnostics and parameter checks with illustrations.
- DESCRIPTION & OPERATION
- AIR BAG LIGHT
- IMPACT SENSORS
- AIR BAG MODULE
- AIR BAG SYSTEM DIAGNOSTIC MODULE (ASDM)
- DIAGNOSTIC CONNECTOR
- CLOCKSPRING
- SERVICING
- SERVICE PRECAUTIONS
- DISABLING & ACTIVATING AIR BAG SYSTEM
- DISABLING & ACTIVATING SYSTEM FOR REPAIRS
- COMPLETE SYSTEM DEACTIVATION
- POST-COLLISION INSPECTION
- CLOCKSPRING CENTERING - STANDARD COLUMN
- CLOCKSPRING CENTERING - TILT COLUMN
- DEPLOYED AIR BAG CLEAN-UP
- UNDEPLOYED AIR BAG DISPOSAL PROCEDURES
- PROCEDURE 1: ELECTRONIC DEPLOYMENT WITH INTACT WIRING
- PROCEDURE 2: REMOTE DEPLOYMENT OF AIR BAG
- Removal
- Installation
- AIR BAG MODULE & STEERING WHEEL
- TESTING - SYSTEM OPERATION CHECK
- DIAGNOSIS & TESTING
- SELF-DIAGNOSTIC SYSTEM
- Fault Codes
- Stored Codes
- Erase Stored Codes
- Volt-Ohmmeter Function
- PRETEST INSPECTION & DIAGNOSTIC PROCEDURE
- ENTERING ON-BOARD DIAGNOSTICS
- SYSTEM TESTING - DIAGNOSTIC CHARTS
- WIRE REPAIR
- REPAIRING BROKEN OR CUT WIRES
- BLADE & SEALED PIN TERMINALS
- PIN HEADER TERMINALS
- REPLACING TERMINALS
- TORQUE SPECIFICATIONS
- INTRODUCTION
- HARD FAILURES
- INTERMITTENT FAILURES
- DIAGNOSTIC PROCEDURE
- * PLEASE READ THIS FIRST *
- CHECK ENGINE LIGHT DIAGNOSTIC MODE
- DRB-II DIAGNOSTIC MODE
- START COUNTER
- FAULT COUNTER
- DRB-II SWITCH TEST MODE
- DRB-II READ INPUT STATES
- DRB-II READ OUTPUT STATES
- DRB-II ACTUATES SOLENOIDS & RELAYS
- DRB-II ACTUATES OUTPUTS
- DRB-II READ SENSOR VOLTAGES
- DRB-II READ SENSOR VALUES
- DRB-II ENGINE PARAMETERS
- DRB-II SET ENGINE RPM
- DRB-II EMISSIONS EMR TESTS
- DRB-II READ MODULE INFORMATION
- DRB-II SYSTEM MONITORS
- DRB-II SPECIAL FUNCTIONS
- BLANK MESSAGE SCREEN
- NO RESPONSE MESSAGE
- DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION (NON-TURBO)
- DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION (TURBO)
- EMISSION MAINTENANCE REMINDER (EMR) MILEAGE TRANSFER
- EMISSION MAINTENANCE REMINDER (EMR) LIGHT RESET PROCEDURE
- CLEARING CODES
- VEHICLE SECURITY SYSTEM DIAGNOSIS
- SUMMARY
- CODE CHARTS FOR NON-TURBO — Part 1
- CODE CHARTS FOR NON-TURBO — Part 2
- CODE CHARTS FOR NON-TURBO — Part 3
- INTRODUCTION
- SYSTEM DIAGNOSIS
- HARD FAILURES
- INTERMITTENT FAILURES
- DIAGNOSTIC PROCEDURE
- * PLEASE READ THIS FIRST *
- CHECK ENGINE LIGHT DIAGNOSTIC MODE
- DRB-II DIAGNOSTIC MODE
- START COUNTER
- FAULT COUNTER
- DRB-II SWITCH TEST MODE
- DRB-II READ INPUT STATES
- DRB-II READ OUTPUT STATES
- DRB-II ACTUATES SOLENOIDS & RELAYS
- DRB-II ACTUATES OUTPUTS
- DRB-II READ SENSOR VOLTAGES
- DRB-II READ SENSOR VALUES
- DRB-II ENGINE PARAMETERS
- DRB-II SET ENGINE RPM
- DRB-II EMISSIONS EMR TESTS
- DRB-II READ MODULE INFORMATION
- DRB-II SYSTEM MONITORS
- DRB-II SPECIAL FUNCTIONS
- BLANK MESSAGE SCREEN
- NO RESPONSE MESSAGE
- DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION
- EMISSION MAINTENANCE REMINDER (EMR) MILEAGE TRANSFER
- EMISSION MAINTENANCE REMINDER (EMR) LIGHT RESET PROCEDURE
- CLEARING CODES
- VEHICLE SECURITY SYSTEM DIAGNOSIS
- SUMMARY
- CODE CHARTS FOR 2.5L NON-TURBO
- NS6: CHECK FUEL FILTER, FUEL PUMP, PRESSURE REGULATOR
- NS7: CHECK FOR FLOODING FUEL INJ., KINKED FUEL LINES
- NS12: CHECK FOR SYSTEM PWR & GND, OPERATION OF MAP
- NS15: CHECKING ASD RELAY, POWER FEED TO FUEL PUMP
- NS5: CHECK FOR FUEL FILTER, FUEL PUMP
- NS6: CHECK FOR HIGH FUEL PRESSURE AT PRESSURE
- NS9: CHECK FOR SYSTEM PWR & GND, OPERATION OF MAP — Part 1
- NS9: CHECK FOR SYSTEM PWR & GND, OPERATION OF MAP — Part 2