FLUID CAPACITIES
| Application | Refill Qts. (L) | Dry Fill Qts. (L) |
|---|
| Dakota & Durango |
| 42RE. 44RE & 46RE | 1.5 (1.4) (2) | (3) 9.5-11.4 (9.0-10.8) |
| Ram Pickup |
| 42RE | 1.5 (1.4) (2) | (3) 8.5-11.0 (8.0-10.4) |
| 46RE | 1.5 (1.4) (2) | (3) 8.7-13.0 (8.2-12.3) |
| 47RE | 1.5 (1.4) (2) | (3) 8.7-16.9 (8.2-16.0) |
| Ram Van/Wagon |
| 32RH & 36RH | 1.5 (1.4) (2) | (3) 8.5-9.0 (8.0-8.5) |
| 46RE | 1.5 (1.4) (2) | (3) 11.4-11.6 (10.8-11.0) |
| (1) Approximate quantity listed. (2) Add fluid until fluid level is at MIN arrow mark on dipstick. Start engine and allow engine to idle. With brakes applied, shift transmission through all gears and back to Neutral. Add additional fluid to bring fluid level to MIN mark on dipstick. Recheck fluid level with transmission at normal operating temperature. Adjust fluid level to MAX arrow mark on dipstick. (3) Quantity may vary by type of oil cooler and oil cooler lines. |
| (1) | Approximate quantity listed. |
| (2) | Add fluid until fluid level is at MIN arrow mark on dipstick. Start engine and allow engine to idle. With brakes applied, shift transmission through all gears and back to Neutral. Add additional fluid to bring fluid level to MIN mark on dipstick. Recheck fluid level with transmission at normal operating temperature. Adjust fluid level to MAX arrow mark on dipstick. |
| (3) | Quantity may vary by type of oil cooler and oil cooler lines. |
TRANSMISSION REFILL CAPACITIES (1)
| Application | Pts. (L) |
|---|
| Dakota & Durango |
| NV231 | 2.5 (1.2) |
| NV242 | 2.8 (1.4) |
| Ram Pickup |
| 1500 | 2.5 (1.2) |
| 2500 & 3500 |
| 2WD With Power Take-Off (PTO) Adapter | 9.0 (4.3) |
| 5.9L Diesel & V10 | 6.5 (3.1) |
| All Others | 5.0 (2.4) |
| (1) Approximate quantity listed. |
| (1) | Approximate quantity listed. |
TRANSFER CASE REFILL CAPACITIES (1)
| Application | Pts. (L) |
|---|
| Ram Pickup |
| 2WD 2500 & 3500 | 4.6 (2.2) |
| (1) Approximate quantity listed. |
| (1) | Approximate quantity listed. |
POWER TAKE-OFF (PTO) ADAPTER REFILL CAPACITIES (1)
- Raise and support vehicle. Loosen oil pan bolts, allowing fluid to drain from oil pan. Remove oil pan bolts, oil pan and gasket. Remove oil filter bolts and oil filter from valve body.
- Adjust kickdown band and low-reverse bands if necessary. See «KICKDOWN BAND»(ref-1907-S34030897762000031500000) and «LOW-REVERSE BAND»(ref-1907-S04900472722000031500000) under ADJUSTMENTS.
- Clean oil pan, magnet and all sealing surfaces. Install NEW oil filter. Install and tighten oil filter bolts to specification. See «TORQUE SPECIFICATIONS»(ref-1907-S36236128362000031500000) .
- Using NEW gasket, install oil pan. Install and tighten oil pan bolts to specification. See «TORQUE SPECIFICATIONS»(ref-1907-S36236128362000031500000) .
- Add Mopar ATF Plus Type 7176 fluid until fluid level is at MIN arrow mark on dipstick. Start engine and allow engine to idle. With brakes applied, shift transmission through all gears and back to Neutral.
- Add additional fluid to bring fluid level to MIN mark on dipstick. Recheck fluid level with transmission at normal operating temperature. Adjust fluid level to MAX arrow mark on dipstick. DO NOT overfill transmission.
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) |
|---|
| Kickdown Band Adjusting Screw Lock Nut | 30 (41) |
| Low-Reverse Band Adjusting Screw Lock Nut | 25 (34) |
| Oil Pan Bolt | 12 (16) |
| PTO Adapter Drain Plug (Ram Pickup) | 40 (54) |
| PTO Adapter Fill Plug (Ram Pickup) | 40 (54) |
| Transfer Case Drain Plug | 40 (54) |
| Transfer Case Fill Plug | 40 (54) |
| INCH Lbs. (N.m) |
| Oil Filter Bolt | 35 (4.0) |
