Set Conditions Dodge Durango II

Set Conditions

1. Set Condition: The Seat Memory Module detects a low signal circuit voltage that is not within voltage specification from the Adjustable Pedal Sensor.

Possible Causes

1. CONNECTOR/TERMINAL DAMAGE
2. (G11) ADJUSTABLE PEDALS SENSOR SUPPLY CIRCUIT SHORTED TO GROUND, OR OPEN
3. (G12) ADJUSTABLE PEDALS SENSOR SIGNAL CIRCUIT SHORTED TO GROUND, OR OPEN
4. ADJUSTABLE PEDALS SENSOR - INTERNAL FAULT
5. SEAT MEMORY MODULE - INTERNAL FAULT

Scheme 8

Scheme 9

Scheme 10

Scheme 11

Scheme 12

Scheme 13

Scheme 14

Scheme 15

1. CHECK FOR DTC B1D56-ADJUSTABLE PEDAL SENSOR CIRCUIT LOW NOTE: This DTC must be active for the results of this test to be valid. Turn the ignition on. With the scan tool, record and erase DTC's. Cycle the ignition switch from off to on. Cycle the Adjustable Pedals Switch forward and rearward. With the scan tool, read DTC's Does the scan tool display: B1D56-ADJUSTABLE PEDAL SENSOR CIRCUIT LOW? Yes : Go To 2 No : Refer to «APS - INTERMITTENT CONDITION»(ref-212743-S04103463772005122700000) , diagnostic procedure. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .
2. CHECK CONNECTOR/TERMINAL FOR DAMAGE NOTE: Check all terminals for broken, bent, pushed out, or corroded terminals. Turn the ignition off. Inspect the Seat Memory Module harness connector, Adjustable Pedals Sensor, and Adjustable Pedals Sensor harness connector. Is the Adjustable Pedals Sensor or any of the connectors/terminals damaged? Yes : Repair as necessary. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Go To 3
3. CHECK (G11) ADJUSTABLE PEDALS SENSOR SUPPLY CIRCUIT FOR A SHORT TO GROUND Turn the ignition off. Disconnect the Seat Memory Module harness connector. Disconnect the Adjustable Pedals Sensor harness connector. Using a 12-volt test light connected to 12-volts, probe the (G11) Adjustable Pedals Sensor Supply circuit. Does the test light illuminate brightly? Yes : Repair the (G11) Adjustable Pedals Sensor Supply circuit for a short to ground. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Go To 4
4. CHECK (G11) ADJUSTABLE PEDALS SENSOR SUPPLY CIRCUIT FOR AN OPEN Turn the ignition off. Disconnect the Seat Memory Module harness connector. Disconnect the Adjustable Pedals Sensor harness connector. Connect a jumper wire between the (G11) Adjustable Pedals Sensor Supply circuit and ground. Using a 12-volt test light connected to 12-volts, probe the (G11) Adjustable Pedals Sensor Supply circuit. Does the test light illuminate brightly Yes : Go To 5 No : Repair the (G11) Adjustable Pedals Sensor Supply circuit for an open. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .
5. CHECK (G12) ADJUSTABLE PEDALS SENSOR SIGNAL CIRCUIT FOR A SHORT TO GROUND Turn the ignition off. Disconnect the Seat Memory Module harness connector. Disconnect the Adjustable Pedals Sensor harness connector. Using a 12-volt test light connected to 12-volts, probe the (G12) Adjustable Pedals Sensor Signal circuit. Does the test light illuminate brightly? Yes : Repair the (G12) Adjustable Pedals Sensor Signal circuit for a short to ground. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Go To 6
6. CHECK (G12) ADJUSTABLE PEDALS SENSOR SIGNAL CIRCUIT FOR AN OPEN Turn the ignition off. Disconnect the Seat Memory Module harness connector. Disconnect the Adjustable Pedals Sensor harness connector. Connect a jumper wire between the (G12) Adjustable Pedals Sensor Signal circuit and ground. Using a 12-volt test light connected to 12-volts, probe the (G12) Adjustable Pedals Sensor Signal circuit. Does the test light illuminate brightly? Yes : Go To 7 No : Repair the (G12) Adjustable Pedals Sensor Signal circuit for an open. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .
7. CHECK (G11) ADJUSTABLE PEDALS SENSOR SUPPLY CIRCUIT VOLTAGE Turn the ignition off. Disconnect the Adjustable Pedals Sensor harness connector. Measure the voltage between the (G11) Adjustable Pedals Sensor Supply circuit and ground. Is the voltage between 4.0 and 5.0 volts? Yes : Go To 8 No : Replace and reprogram the Seat Memory Module in accordance with the Service Information. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .
8. CHECK (G12) ADJUSTABLE PEDALS SENSOR SIGNAL CIRCUIT VOLTAGE Turn the ignition off. Reconnect all connectors. Measure the voltage of the (G12) Adjustable Pedals Sensor Signal circuit in the Seat Memory Module harness connector. Is the voltage above 0.5 volts? Yes : Replace and reprogram the Seat Memory Module in accordance with the Service Information. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Replace the Adjustable Pedals Sensor in accordance with the Service Information. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .

Scheme 16

1. When Monitored: The Adjustable Pedal Motor is in active operation.

1. Set Condition: The Seat Memory Module detects a high signal circuit voltage that is not within voltage specification from the Adjustable Pedal Sensor.

Possible Causes

1. CONNECTOR/TERMINAL DAMAGE
2. (G11) ADJUSTABLE PEDALS SENSOR SUPPLY CIRCUIT SHORTED TO VOLTAGE
3. (G12) ADJUSTABLE PEDALS SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
4. ADJUSTABLE PEDALS SENSOR - INTERNAL FAULT
5. SEAT MEMORY MODULE - INTERNAL FAULT

Scheme 17

Scheme 18

Scheme 19

Scheme 20

Scheme 21

1. CHECK FOR DTC B1D57-ADJUSTABLE PEDAL SENSOR CIRCUIT HIGH NOTE: This DTC must be active for the results of this test to be valid. Turn the ignition on. With the scan tool, record and erase DTC's. Cycle the ignition switch from off to on. Cycle the Adjustable Pedals Switch forward and rearward. With the scan tool, read DTC's Does the scan tool display: B1D57-ADJUSTABLE PEDAL SENSOR CIRCUIT HIGH? Yes : Go To 2 No : Refer to «APS - INTERMITTENT CONDITION»(ref-212743-S04103463772005122700000) , diagnostic procedure. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .
2. CHECK CONNECTOR/TERMINAL FOR DAMAGE NOTE: Check all terminals for broken, bent, pushed out, or corroded terminals. Turn the ignition off. Inspect the Seat Memory Module harness connector, Adjustable Pedals Sensor, and Adjustable Pedals Sensor harness connector. Is the Adjustable Pedals Sensor or any of the connectors/terminals damaged? Yes : Repair as necessary. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Go To 3
3. CHECK (G11) ADJUSTABLE PEDALS SENSOR SUPPLY CIRCUIT FOR A SHORT TO VOLTAGE Turn the ignition off. Disconnect the Seat Memory Module harness connector. Turn the ignition on. Measure the voltage between the (G11) Adjustable Pedals Sensor Supply circuit and ground. Is the voltage above 5.0 volts? Yes : Repair the (G11) Adjustable Pedals Sensor Supply circuit for a short to voltage. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Go To 4
4. CHECK (G12) ADJUSTABLE PEDALS SENSOR SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE Turn the ignition off. Disconnect the Seat Memory Module harness connector. Turn the ignition on. Measure the voltage between the (G12) Adjustable Pedals Sensor Signal circuit and ground. Is the voltage above 5.0 volts? Yes : Repair the (G12) Adjustable Pedals Sensor Signal circuit for a short to voltage. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Go To 5
5. CHECK (G12) ADJUSTABLE PEDALS SENSOR SIGNAL CIRCUIT VOLTAGE Turn the ignition off. Reconnect all connectors. Measure the voltage of the (G12) Adjustable Pedals Sensor Signal circuit in the Seat Memory Module harness connector. Is the voltage below 4.0 volts? Yes : Replace and reprogram the Seat Memory Module in accordance with the Service Information. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Replace the Adjustable Pedals Sensor in accordance with the Service Information. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .

Scheme 22

1. When Monitored: The Adjustable Pedals Switch is in active operation.

1. Set Condition: The Seat Memory Module detects an activation of both pedal switches at the same time.

Possible Causes

1. CONNECTOR/TERMINAL DAMAGE
2. (Q100) ADJUSTABLE PEDALS SWITCH REARWARD CIRCUIT SHORTED TO GROUND
3. (Q900) ADJUSTABLE PEDALS SWITCH FORWARD CIRCUIT SHORTED TO GROUND
4. (Q100) ADJUSTABLE PEDALS SWITCH REARWARD CIRCUIT AND (Q900) ADJUSTABLE PEDALS SWITCH FORWARD CIRCUIT SHORTED TOGETHER
5. ADJUSTABLE PEDALS SWITCH - INTERNAL FAULT
6. SEAT MEMORY MODULE - INTERNAL FAULT

Scheme 23

Scheme 24

Scheme 25

Scheme 26

Scheme 27

Scheme 28

1. CHECK FOR DTC B1D5B-ADJUSTABLE PEDAL SWITCH CIRCUIT PERFORMANCE NOTE: This DTC must be active for the results of this test to be valid. Turn the ignition on. With the scan tool, record and erase DTC's. Cycle the ignition switch from off to on. Cycle the Adjustable Pedals Switch forward and rearward. With the scan tool, read DTC's Does the scan tool display: B1D5B-ADJUSTABLE PEDAL SWITCH CIRCUIT PERFORMANCE? Yes : Go To 2 No : Refer to «APS - INTERMITTENT CONDITION»(ref-212743-S04103463772005122700000) , diagnostic procedure. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .
2. CHECK CONNECTOR/TERMINAL FOR DAMAGE NOTE: Check all terminals for broken, bent, pushed out, or corroded terminals. Turn the ignition off. Inspect the Seat Memory Module harness connector, Adjustable Pedals Switch, and Adjustable Pedals Switch harness connector. Is the Adjustable Pedals Switch or any of the connectors/terminals damaged? Yes : Repair as necessary. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Go To 3
3. CHECK (Q100) ADJUSTABLE PEDALS SWITCH REARWARD CIRCUIT FOR A SHORT TO GROUND Turn the ignition off. Disconnect the Seat Memory Module harness connector. Disconnect the Adjustable Pedals Switch harness connector. Using a 12-volt test light connected to 12-volts, probe the (Q100) Adjustable Pedals Switch Rearward circuit. Does the test light illuminate brightly? Yes : Repair the (Q100) Adjustable Pedals Switch Rearward circuit for a short to ground. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Go To 4
4. CHECK (Q900) ADJUSTABLE PEDALS SWITCH FORWARD CIRCUIT FOR A SHORT TO GROUND Turn the ignition off. Disconnect the Seat Memory Module harness connector. Disconnect the Adjustable Pedals Switch harness connector. Using a 12-volt test light connected to 12-volts, probe the (Q900) Adjustable Pedals Switch Forward circuit. Does the test light illuminate brightly? Yes : Repair the (Q900) Adjustable Pedals Switch Forward circuit for a short to ground. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Go To 5
5. CHECK (Q100) ADJUSTABLE PEDALS SWITCH REARWARD CIRCUIT AND (Q900) ADJUSTABLE PEDALS SWITCH FORWARD CIRCUIT FOR A SHORT TOGETHER Turn the ignition off. Disconnect the Seat Memory Module harness connector. Disconnect the Adjustable Pedals Switch harness connector. Measure the resistance between the (Q100) Adjustable Pedals Switch Rearward circuit and (Q900) Adjustable Pedals Switch Forward circuit. Is the resistance above 5.0 ohms? Yes : Go To 6 No : Repair the (Q100) Adjustable Pedals Switch Rearward circuit and (Q900) Adjustable Pedals Switch Forward circuit for a short together. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .
6. CHECK ADJUSTABLE PEDALS SWITCH SHORTED Turn the ignition off. Disconnect the Adjustable Pedals Switch harness connector. Measure the resistance between the (Q100) Adjustable Pedals Switch Rearward and (Q900) Adjustable Pedals Switch Forward terminals at the Adjustable Pedals Switch. Is the resistance below 5.0 ohms? Yes : Replace and reprogram the Seat Memory Module in accordance with the Service Information. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Replace the Adjustable Pedals Switch in accordance with the Service Information. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .

Scheme 29

1. When Monitored: The Adjustable Pedals Switch is in active operation.

1. Set Condition: The Seat Memory Module detects that the Adjustable Pedals Switch has been activated for a time period of more than 50 seconds.

Possible Causes

1. CONNECTOR/TERMINAL DAMAGE
2. (Q900) ADJUSTABLE PEDALS SWITCH FORWARD CIRCUIT SHORTED TO GROUND
3. ADJUSTABLE PEDALS SWITCH - INTERNAL FAULT
4. SEAT MEMORY MODULE - INTERNAL FAULT

Scheme 30

Scheme 31

Scheme 32

Scheme 33

1. CHECK FOR DTC B1D5C-ADJUSTABLE PEDAL SWITCH CIRCUIT STUCK FORWARD NOTE: This DTC must be active for the results of this test to be valid. Turn the ignition on. With the scan tool, record and erase DTC's. Cycle the ignition switch from off to on. Cycle the Adjustable Pedals Switch forward and rearward. With the scan tool, read DTC's Does the scan tool display: B1D5C-ADJUSTABLE PEDAL SWITCH CIRCUIT STUCK FORWARD? Yes : Go To 2 No : Refer to «APS - INTERMITTENT CONDITION»(ref-212743-S04103463772005122700000) diagnostic procedure. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .
2. CHECK CONNECTOR/TERMINAL FOR DAMAGE NOTE: Check all terminals for broken, bent, pushed out, or corroded terminals. Turn the ignition off. Inspect the Seat Memory Module harness connector, Adjustable Pedals Switch, and Adjustable Pedals Switch harness connector. Is the Adjustable Pedals Switch or any of the connectors/terminals damaged? Yes : Repair as necessary. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Go To 3
3. CHECK (Q900) ADJUSTABLE PEDALS SWITCH FORWARD CIRCUIT FOR A SHORT TO GROUND Turn the ignition off. Disconnect the Seat Memory Module harness connector. Disconnect the Adjustable Pedals Switch harness connector. Using a 12-volt test light connected to 12-volts, probe the (Q900) Adjustable Pedals Switch Forward circuit. Does the test light illuminate brightly? Yes : Repair the (Q900) Adjustable Pedals Switch Forward circuit for a short to ground. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Go To 4
4. CHECK ADJUSTABLE PEDALS SWITCH SHORTED Turn the ignition off. Disconnect the Adjustable Pedals Switch harness connector. Measure the resistance between the (Q100) Adjustable Pedals Switch Rearward and (Q900) Adjustable Pedals Switch Forward terminals at the Adjustable Pedals Switch. Is the resistance below 5.0 ohms? Yes : Replace and reprogram the Seat Memory Module in accordance with the Service Information. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Replace the Adjustable Pedals Switch in accordance with the Service Information. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .

Scheme 34

1. When Monitored: The Adjustable Pedals Switch is in active operation.

1. Set Condition: The Seat Memory Module detects that the Adjustable Pedals Switch has been activated for a time period of more than 50 seconds.

Possible Causes

1. CONNECTOR/TERMINAL DAMAGE
2. (Q100) ADJUSTABLE PEDALS SWITCH FORWARD CIRCUIT SHORTED TO GROUND
3. ADJUSTABLE PEDALS SWITCH - INTERNAL FAULT
4. SEAT MEMORY MODULE - INTERNAL FAULT

Scheme 35

Scheme 36

Scheme 37

Scheme 38

1. CHECK FOR DTC B1D5D-ADJUSTABLE PEDAL SWITCH CIRCUIT STUCK REARWARD NOTE: This DTC must be active for the results of this test to be valid. Turn the ignition on. With the scan tool, record and erase DTC's. Cycle the ignition switch from off to on. Cycle the Adjustable Pedals Switch forward and rearward. With the scan tool, read DTC's Does the scan tool display: B1D5D-ADJUSTABLE PEDAL SWITCH CIRCUIT STUCK REARWARD? Yes : Go To 2 No : Refer to «APS - INTERMITTENT CONDITION»(ref-212743-S04103463772005122700000) diagnostic procedure. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .
2. CHECK CONNECTOR/TERMINAL FOR DAMAGE NOTE: Check all terminals for broken, bent, pushed out, or corroded terminals. Turn the ignition off. Inspect the Seat Memory Module harness connector, Adjustable Pedals Switch, and Adjustable Pedals Switch harness connector. Is the Adjustable Pedals Switch or any of the connectors/terminals damaged? Yes : Repair as necessary. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Go To 3
3. CHECK (Q100) ADJUSTABLE PEDALS SWITCH REARWARD CIRCUIT FOR A SHORT TO GROUND Turn the ignition off. Disconnect the Seat Memory Module harness connector. Disconnect the Adjustable Pedals Switch harness connector. Using a 12-volt test light connected to 12-volts, probe the (Q100) Adjustable Pedals Switch Rearward circuit. Does the test light illuminate brightly? Yes : Repair the (Q100) Adjustable Pedals Switch Rearward circuit for a short to ground. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Go To 4
4. CHECK ADJUSTABLE PEDALS SWITCH SHORTED Turn the ignition off. Disconnect the Adjustable Pedals Switch harness connector. Measure the resistance between the (Q100) Adjustable Pedals Switch Rearward and (Q900) Adjustable Pedals Switch Forward terminals at the Adjustable Pedals Switch. Is the resistance below 5.0 ohms? Yes : Replace and reprogram the Seat Memory Module in accordance with the Service Information. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Replace the Adjustable Pedals Switch in accordance with the Service Information. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .

Scheme 39

1. When Monitored: The Adjustable Pedals Motor is in active operation.

1. Set Condition: The Seat Memory Module detects that the Adjustable Pedals Motor has been activated for a time period and has not spun with three motor direction commands.

Possible Causes

1. CONNECTOR/TERMINAL DAMAGE
2. MECHANICAL FAILURE IN THE ADJUSTABLE PEDALS
3. (P205) ADJUSTABLE PEDALS MOTOR FORWARD CIRCUIT OPEN
4. (P206) ADJUSTABLE PEDALS MOTOR REARWARD CIRCUIT OPEN
5. (G912) ADJUSTABLE PEDALS SENSOR RETURN CIRCUIT OPEN
6. ADJUSTABLE PEDALS MOTOR - INTERNAL FAULT
7. SEAT MEMORY MODULE - INTERNAL FAULT

Scheme 40

Scheme 41

Scheme 42

Scheme 43

Scheme 44

Scheme 45

1. CHECK FOR DTC B1D67-ADJUSTABLE PEDAL CONTROL CIRCUIT PERFORMANCE NOTE: This DTC must be active for the results of this test to be valid. Turn the ignition on. With the scan tool, record and erase DTC's. Cycle the ignition switch from off to on. Cycle and hold the Adjustable Pedals Switch forward, rearward, and forward at two second intervals. With the scan tool, read DTC's Does the scan tool display: B1D67-ADJUSTABLE PEDAL CONTROL CIRCUIT PERFORMANCE? Yes : Go To 2 No : Refer to «APS - INTERMITTENT CONDITION»(ref-212743-S04103463772005122700000) diagnostic procedure. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .
2. CHECK CONNECTOR/TERMINAL FOR DAMAGE NOTE: Check all terminals for broken, bent, pushed out, or corroded terminals. Turn the ignition off. Inspect the Seat Memory Module harness connector, Adjustable Pedals Motor, and Adjustable Pedals Motor harness connector. Is the Adjustable Pedals Motor or any of the connectors/terminals damaged? Yes : Repair as necessary. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Go To 3
3. CHECK ADJUSTABLE PEDALS ASSEMBLY FOR MECHANICAL DAMAGE Turn the ignition off. Inspect the Adjustable Pedals Assembly for any physical damage. NOTE: Check for any conditions that would cause the motor to stall or be stuck. Is the Adjustable Pedals Assembly damaged or broken? Yes : Replace the Adjustable Pedals Assembly in accordance with the Service Information. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Go To 4
4. CHECK (P205) ADJUSTABLE PEDALS MOTOR FORWARD CIRCUIT FOR AN OPEN Turn the ignition off. Disconnect the Seat Memory Module harness connector. Disconnect the Adjustable Pedals Motor harness connector Connect a jumper wire between the (P205) Adjustable Pedals Motor Forward circuit and ground. Using a 12-volt test light connected to 12-volts, probe the (P205) Adjustable Pedals Motor Forward circuit. Does the test light illuminate brightly? Yes : Go To 5 No : Repair the (P205) Adjustable Pedals Motor Forward circuit for an open. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .
5. CHECK (P206) ADJUSTABLE PEDALS MOTOR REARWARD CIRCUIT FOR AN OPEN Turn the ignition off. Disconnect the Seat Memory Module harness connector. Disconnect the Adjustable Pedals Motor harness connector Connect a jumper wire between the (P206) Adjustable Pedals Motor Rearward circuit and ground. Using a 12-volt test light connected to 12-volts, probe the (P206) Adjustable Pedals Motor Rearward circuit. Does the test light illuminate brightly? Yes : Go To 6 No : Repair the (P206) Adjustable Pedals Motor Rearward circuit for an open. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .
6. CHECK (G912) ADJUSTABLE PEDALS SENSOR RETURN CIRCUIT FOR AN OPEN Turn the ignition off. Disconnect the Seat Memory Module harness connector. Disconnect the Adjustable Pedals Sensor harness connector Connect a jumper wire between the (G912) Adjustable Pedals Sensor Return circuit and ground. Using a 12-volt test light connected to 12-volts, probe the (G912) Adjustable Pedals Sensor Return circuit. Does the test light illuminate brightly? Yes : Go To No : Repair the (G912) Adjustable Pedals Sensor Return circuit for an open. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .
7. CHECK ADJUSTABLE PEDALS MOTOR Turn the ignition off. Disconnect the Adjustable Pedals Motor harness connector. Measure the resistance between the (P205) Adjustable Pedals Motor Forward and (P206) Adjustable Pedals Motor Rearward terminals at the Adjustable Pedals Motor. Is the resistance below 100.0 ohms? Yes : Replace and reprogram the Seat Memory Module in accordance with the Service Information. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) . No : Replace the Adjustable Pedals Motor in accordance with the Service Information. Perform «APS VERIFICATION TEST - VER 1»(ref-212743-S12067490052005122700000) .