2WD Models
Center steering wheel and hold with steering wheel clamp. Loosen tie rod lock nuts. Rotate rods to set toe to specifications. See ALIGNMENT SPECIFICATIONS . Tighten tie rod lock nuts to specification. See TORQUE SPECIFICATIONS . Adjust steering gear to tie rod boots at tie rod. Remove steering wheel clamp.
4WD Models
Center steering wheel and hold with steering wheel clamp. Loosen tie rod adjustment sleeve clamp bolts. Rotate adjustment sleeve to align toe to specifications. See ALIGNMENT SPECIFICATIONS . Position sleeve clamps on underside of sleeve so clamp ends are not over sleeve slot, and tighten adjustment sleeve clamp bolts to specification. See TORQUE SPECIFICATIONS . Remove steering wheel clamp.
| Application | Preferred | Range |
|---|---|---|
| Camber (Degrees) Front | 0.5 | 0 to 1 |
| Camber (Degrees) Rear | N/A | N/A |
| Caster (Degrees) Front | 1.5 | 0.5 to 2.5 |
| Caster (Degrees) Rear | N/A | N/A |
| Toe-In (Inches) Front | 0.13 | 0.08 to 0.18 |
| Toe-In (Inches) Rear | N/A | N/A |
| Toe-In (Millimeters) Front | 3.5 | 2 to 4.5 |
| Toe-In (Millimeters) Rear | N/A | N/A |
| Toe-In (Degrees) Front | 0.25 | 0.15 to 0.35 |
| Toe-In (Degrees) Rear | N/A | N/A |
| Wheelbase (Inches - Club Cab) | N/A | 112 |
| Wheelbase (Millimeters - Club Cab) | N/A | 2845 |
| Wheelbase (Inches - Long Bed) | N/A | 124 |
| Wheelbase (Millimeters - Long Bed) | N/A | 3147 |
| Wheelbase (Inches - Short Bed) | N/A | 131 |
| Wheelbase (Millimeters - Short Bed) | N/A | 3325 |
WHEEL ALIGNMENT SPECIFICATIONS
| Application | Ft. Lbs. (N.m) | ||
|---|---|---|---|
| Front Suspension (2WD) | |||
| Lower Ball Stud Nut | 135 (183) | ||
| Lower Control Arm Pivot Bolt | |||
| Front Nut | 130 (176) | ||
| Rear Nut | 80 (108) | ||
| Shock Absorber | |||
| Lower Bolt | 17 (23) | ||
| Upper Nut | 25 (34) | ||
| Upper Ball Stud Nut | 105 (142) | ||
| Upper Control Arm Pivot Bar Nut | 155 (210) | ||
| Rear Suspension (2WD) | |||
| Shock Absorber Nut | 60 (81) | ||
| U-Bolt Nuts | 65 (88) | ||
| Wheel Lug Nuts | 85 (115) | ||
TORQUE SPECIFICATIONS (2WD)
| Application | Ft. Lbs. (N.m) | ||
|---|---|---|---|
| Front Suspension (4WD) | |||
| Lower Ball Stud Nut | 120 (163) | ||
| Lower Control Arm Pivot Bolt | |||
| Front Nut | 80 (108) | ||
| Rear Nut | 130 (176) | ||
| Shock Absorber | |||
| Lower Bolt | 100 (136) | ||
| Upper Nut | 25 (34) | ||
| Upper Ball Stud Nut | 105 (142) | ||
| Upper Control Arm Pivot Bar Nut | 155 (210) | ||
| Rear Suspension (4WD) | |||
| Shock Absorber Nut | 60 (81) | ||
| U-Bolt Nuts | 110 (149) | ||
| Wheel Lug Nuts | 85 (115) | ||
TORQUE SPECIFICATIONS (4WD)