Home ReviewsRefund
Home/Dodge/Challenger/Dodge Challenger III (2008-2010)/Repair manual/Entertainment Systems/Audio System (Amplifier) - Electrical Diagnostics: Other
Contents Wiring diagrams Section: Entertainment Systems All sections

Audio System (Amplifier) - Electrical Diagnostics: Other Dodge Challenger III

Entertainment Systems ~1234 words

Monitor Conditions

  1. When Monitored: With the ignition on.

Set Conditions

  1. Set Condition: This Diagnostic Trouble Code (DTC) sets if a Direct Current (DC) offset occurs on the output channel, the amplifier shall set a DTC after a maturity rate of four to six seconds.

Possible Causes

Possible Causes
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The Amplifier detects a shorted to ground condition on the speaker output circuit.
Possible Causes
(X209) AMPLIFIED LEFT INSTRUMENT PANEL (I/P) SPEAKER (+) CIRCUIT SHORTED TO GROUND
(X299) AMPLIFIED LEFT INSTRUMENT PANEL (I/P) SPEAKER (-) CIRCUIT SHORTED TO GROUND
LEFT INSTRUMENT PANEL SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The Amplifier detects a short to battery condition on the speaker output circuit.
Possible Causes
(X209) AMPLIFIED LEFT INSTRUMENT PANEL (I/P) SPEAKER (+) CIRCUIT SHORTED TO VOLTAGE
(X299) AMPLIFIED LEFT INSTRUMENT PANEL (I/P) SPEAKER (-) CIRCUIT SHORTED TO VOLTAGE
AMPLIFIER
  1. When Monitored: Amplifier bus wake-up. Amplifier reset with scan tool.
  1. Set Condition: The Amplifier detects an open condition on the speaker output circuit.
Possible Causes
(X209) AMPLIFIED LEFT INSTRUMENT PANEL (I/P) SPEAKER (+) CIRCUIT OPEN
(X299) AMPLIFIED LEFT INSTRUMENT PANEL (I/P) SPEAKER (-) CIRCUIT OPEN
LEFT INSTRUMENT PANEL (I/P) SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on. Radio volume at 25 or higher.
  1. Set Condition: The Amplifier detects that the output circuits are shorted together.
Possible Causes
(X209) AMPLIFIED LEFT INSTRUMENT PANEL (I/P) SPEAKER (+) CIRCUIT SHORTED TO THE (X299) AMPLIFIED LEFT INSTRUMENT PANEL (I/P) SPEAKER (-) CIRCUIT
LEFT INSTRUMENT PANEL (I/P) SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: This Diagnostic Trouble Code (DTC) sets if a Direct Current (DC) offset occurs on the output channel, the Amplifier shall set a DTC after a maturity rate of four to six seconds.
Possible Causes
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The amplifier detects a shorted to ground condition on the speaker output circuit.
Possible Causes
(X208) AMPLIFIED RIGHT INSTRUMENT PANEL (I/P) SPEAKER (+) CIRCUIT SHORTED TO GROUND
(X298) AMPLIFIED RIGHT INSTRUMENT PANEL (I/P) SPEAKER (-) CIRCUIT SHORTED TO GROUND
RIGHT INSTRUMENT PANEL (I/P) SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The amplifier detects a short to battery condition on the output circuit.
Possible Causes
(X208) AMPLIFIED RIGHT INSTRUMENT PANEL (I/P) SPEAKER (+) CIRCUIT SHORTED TO VOLTAGE
(X298) AMPLIFIED RIGHT INSTRUMENT PANEL (I/P) SPEAKER (-) CIRCUIT SHORTED TO VOLTAGE
AMPLIFIER
  1. When Monitored: Amplifier BUS wake-up. Amplifier reset with scan tool.
  1. Set Condition: The amplifier detects an open condition on the speaker output circuit.
Possible Causes
(X208) AMPLIFIED RIGHT INSTRUMENT PANEL (I/P) SPEAKER (+) CIRCUIT OPEN
(X298) AMPLIFIED RIGHT INSTRUMENT PANEL (I/P) SPEAKER (-) CIRCUIT OPEN
RIGHT INSTRUMENT PANEL (I/P) SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on. Radio volume at 25 or higher.
  1. Set Condition: The amplifier detects that the output circuits are shorted together.
Possible Causes
(X208) AMPLIFIED RIGHT INSTRUMENT PANEL (I/P) SPEAKER (+) CIRCUIT SHORTED TO THE (X298) AMPLIFIED RIGHT INSTRUMENT PANEL (I/P) SPEAKER (-) CIRCUIT
RIGHT INSTRUMENT PANEL (I/P) SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: This DTC will set if a Direct Current (DC) offset occurs on the output channel, the amplifier shall set a DTC after a maturity rate of 5 ±1 sec.
Possible Causes
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The amplifier detects a shorted to ground condition on the speaker output circuit.
Possible Causes
(X201) AMPLIFIED LEFT FRONT DOOR SPEAKER (+) CIRCUIT SHORTED TO GROUND
(X291) AMPLIFIED LEFT FRONT DOOR SPEAKER (-) CIRCUIT SHORTED TO GROUND
LEFT FRONT DOOR SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The Amplifier detects a short to battery condition on the output circuit.
Possible Causes
(X201) AMPLIFIED LEFT FRONT DOOR SPEAKER (+) CIRCUIT SHORTED TO VOLTAGE
(X291) AMPLIFIED LEFT FRONT DOOR SPEAKER (-) CIRCUIT SHORTED TO VOLTAGE
AMPLIFIER
  1. When Monitored: Amplifier BUS wake-up. Amplifier reset with scan tool.
  1. Set Condition: The amplifier detects an open condition on the speaker output circuit.
Possible Causes
(X201) AMPLIFIED LEFT FRONT DOOR SPEAKER (+) CIRCUIT OPEN
(X291) AMPLIFIED LEFT FRONT DOOR SPEAKER (-) CIRCUIT OPEN
AMPLIFIED LEFT FRONT DOOR SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on. Radio volume at 25 or higher.
  1. Set Condition: The amplifier detects that the output circuits are shorted together.
Possible Causes
(X201) AMPLIFIED LEFT FRONT DOOR SPEAKER (+) CIRCUIT SHORTED TO THE (X291) AMPLIFIED LEFT FRONT DOOR SPEAKER (-) CIRCUIT
AMPLIFIED LEFT FRONT DOOR SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: This Diagnostic Trouble Code (DTC) sets if a Direct Current (DC) offset occurs on the output channel, the Amplifier shall set a DTC after a maturity rate of four to six seconds.
Possible Causes
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The Amplifier detects a shorted to ground condition on the speaker output circuit.
Possible Causes
(X202) AMPLIFIED RIGHT FRONT DOOR SPEAKER (+) CIRCUIT SHORTED TO GROUND
(X292) AMPLIFIED RIGHT FRONT DOOR SPEAKER (-) CIRCUIT SHORTED TO GROUND
RIGHT FRONT DOOR SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The amplifier detects a short to battery condition on the output circuit.
Possible Causes
(X202) AMPLIFIED RIGHT FRONT DOOR SPEAKER (+) CIRCUIT SHORTED TO VOLTAGE
(X292) AMPLIFIED RIGHT FRONT DOOR SPEAKER (-) CIRCUIT SHORTED TO VOLTAGE
AMPLIFIER
  1. When Monitored: Amplifier BUS wake-up. Amplifier reset with scan tool.
  1. Set Condition: The amplifier detects an open condition on the speaker output circuit.
Possible Causes
(X202) AMPLIFIED RIGHT FRONT DOOR SPEAKER (+) CIRCUIT OPEN
(X292) AMPLIFIED RIGHT FRONT DOOR SPEAKER (-) CIRCUIT OPEN
RIGHT FRONT DOOR SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on. Radio volume at 25 or higher.
  1. Set Condition: The amplifier detects that the output circuits are shorted together.
Possible Causes
(X202) AMPLIFIED RIGHT FRONT DOOR SPEAKER (+) CIRCUIT SHORTED TO THE (X292) AMPLIFIED RIGHT FRONT DOOR SPEAKER (-) CIRCUIT
AMPLIFIED RIGHT FRONT DOOR SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: This DTC will set if a DC offset occurs on the output channel, the amplifier shall set a DTC after a maturity rate of 5 ±1 sec.
Possible Causes
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The amplifier detects a shorted to ground condition on the speaker output circuit.
Possible Causes
(X303) AMPLIFIED LEFT REAR SPEAKER (+) CIRCUIT SHORTED TO GROUND
(X393) AMPLIFIED LEFT REAR SPEAKER (-) CIRCUIT SHORTED TO GROUND
AMPLIFIED LEFT REAR SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The amplifier detects a short to battery condition on the output circuit.
Possible Causes
(X303) AMPLIFIED LEFT REAR SPEAKER (+) CIRCUIT SHORTED TO VOLTAGE
(X393) AMPLIFIED LEFT REAR SPEAKER (-) CIRCUIT SHORTED TO VOLTAGE
AMPLIFIER
  1. When Monitored: Amplifier BUS wake-up. Amplifier reset with scan tool.
  1. Set Condition: The amplifier detects an open condition on the speaker output circuit.
Possible Causes
(X303) AMPLIFIED LEFT REAR SPEAKER (+) CIRCUIT OPEN
(X393) AMPLIFIED LEFT REAR SPEAKER (-) CIRCUIT OPEN
AMPLIFIED LEFT REAR SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on. Radio volume at 25 or higher.
  1. Set Condition: The amplifier detects that the output circuits are shorted together.
Possible Causes
(X303) AMPLIFIED LEFT REAR SPEAKER (+) CIRCUIT SHORTED TO THE (X393) AMPLIFIED LEFT REAR SPEAKER (-) CIRCUIT
AMPLIFIED LEFT REAR SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: This DTC will set if a (Direct Current) DC offset occurs on the output channel, the amplifier shall set a DTC after a maturity rate of 5 ±1 sec.
Possible Causes
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The amplifier detects a shorted to ground condition on the speaker output circuit.
Possible Causes
(X304) AMPLIFIED RIGHT REAR SPEAKER (+) CIRCUIT SHORTED TO GROUND
(X394) AMPLIFIED RIGHT REAR SPEAKER (-) CIRCUIT SHORTED TO GROUND
AMPLIFIED RIGHT REAR SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The amplifier detects a short to battery condition on the output circuit.
Possible Causes
(X304) AMPLIFIED RIGHT REAR SPEAKER (+) CIRCUIT SHORTED TO VOLTAGE
(X394) AMPLIFIED RIGHT REAR SPEAKER (-) CIRCUIT SHORTED TO VOLTAGE
AMPLIFIER
  1. When Monitored: Amplifier BUS wake-up. Amplifier reset with scan tool.
  1. Set Condition: The amplifier detects an open condition on the speaker output circuit.
Possible Causes
(X304) AMPLIFIED RIGHT REAR SPEAKER (+) CIRCUIT OPEN
(X394) AMPLIFIED RIGHT REAR SPEAKER (-) CIRCUIT OPEN
AMPLIFIED RIGHT REAR SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on. Radio volume at 25 or higher.
  1. Set Condition: The amplifier detects that the output circuits are shorted together.
Possible Causes
(X304) AMPLIFIED RIGHT REAR SPEAKER (+) CIRCUIT SHORTED TO THE (X394) AMPLIFIED RIGHT REAR SPEAKER (-) CIRCUIT
AMPLIFIED RIGHT REAR SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: This DTC will set if a DC offset occurs on the output channel, the Amplifier shall set a DTC after a maturity rate of 5 ±1 sec.
Possible Causes
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The Amplifier detects a shorted to ground condition on the speaker output circuit.
Possible Causes
(X300) AMPLIFIED SUBWOOFER 1 (+) CIRCUIT SHORTED TO GROUND
(X390) AMPLIFIED SUBWOOFER 1 (-) CIRCUIT SHORTED TO GROUND
SUBWOOFER SPEAKER OR SUBWOOFER AMPLIFIER
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The Amplifier detects a short to battery condition on the output circuit.
Possible Causes
(X300) AMPLIFIED SUBWOOFER 1 (+) CIRCUIT SHORTED TO VOLTAGE
(X390) AMPLIFIED SUBWOOFER 1 (-) CIRCUIT SHORTED TO VOLTAGE
AMPLIFIER
  1. When Monitored: Amplifier BUS wake-up. Amplifier reset with scan tool.
  1. Set Condition: The Amplifier detects an open condition on the speaker output circuits.
Possible Causes
(X300) AMPLIFIED SUBWOOFER 1 (+) CIRCUIT OPEN
(X390) AMPLIFIED SUBWOOFER 1 (-) CIRCUIT OPEN
SUBWOOFER SPEAKER OR SUBWOOFER AMPLIFIER
RADIO AMPLIFIER
  1. When Monitored: With the ignition on. Radio volume at 25 or higher.
  1. Set Condition: The Amplifier detects that the output circuits are shorted together.
Possible Causes
(X300) AMPLIFIED SUBWOOFER 1 (+) CIRCUIT SHORTED TO THE (X390) AMPLIFIED SUBWOOFER 1 (-) CIRCUIT
SUBWOOFER SPEAKER OR SUBWOOFER AMPLIFIER
RADIO AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: This DTC will set if a DC offset occurs on the output channel, the Amplifier shall set a DTC after a maturity rate of 5 ±1 sec.
Possible Causes
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The Amplifier detects a short to ground condition on the speaker output circuit.
Possible Causes
(X200) CENTER INSTRUMENT PANEL (I/P) SPEAKER (+) CIRCUIT SHORTED TO GROUND
(X290) CENTER INSTRUMENT PANEL (I/P) SPEAKER (-) CIRCUIT SHORTED TO GROUND
CENTER INSTRUMENT PANEL (I/P) SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The Amplifier detects a short to battery condition on the output circuit.
Possible Causes
(X200) AMPLIFIED CENTER INSTRUMENT PANEL (I/P) SPEAKER (+) CIRCUIT SHORTED TO VOLTAGE
(X290) AMPLIFIED CENTER INSTRUMENT PANEL (I/P) SPEAKER (-) CIRCUIT SHORTED TO VOLTAGE
AMPLIFIER
  1. When Monitored: Amplifier BUS wake-up. Amplifier reset with scan tool.
  1. Set Condition: The Amplifier detects an open condition on the speaker output circuit.
Possible Causes
(X200) AMPLIFIED CENTER INSTRUMENT PANEL (I/P) SPEAKER (+) CIRCUIT OPEN
(X290) AMPLIFIED CENTER INSTRUMENT PANEL (I/P) SPEAKER (-) CIRCUIT OPEN
CENTER INSTRUMENT PANEL (I/P) SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on. Radio volume at 25 or higher.
  1. Set Condition: The Amplifier detects that the output circuits are shorted together.
Possible Causes
(X200) AMPLIFIED CENTER INSTRUMENT PANEL (I/P) SPEAKER (+) CIRCUIT SHORTED TO THE (X290) AMPLIFIED CENTER INSTRUMENT PANEL (I/P) SPEAKER (-) CIRCUIT
CENTER INSTRUMENT PANEL (I/P) SPEAKER
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: If the cabin EQ message is incompatible with the EQ's stored in the amplifier for 10 consecutive cycles, then the amplifier will set this DTC.
Possible CauseS
NO COMMUNICATION WITH TOTALLY INTEGRATED POWER MODULE
ACTIVE TIPM DTCs
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: If the module detects that the battery voltage is less than 9.0 volts for 1 second.
Possible Causes
VEHICLE CHARGING SYSTEM
(X13) OR (A300) FUSED B(+) OR (Z910) GROUND CIRCUIT HAS HIGH RESISTANCE
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: If the module detects the battery voltage is greater 16.5 volts for one second.
Possible Causes
VEHICLE CHARGING SYSTEM
AMPLIFIER
  1. When Monitored: With the ignition on.
  1. Set Condition: The amplifier detects a software checksum test failure.
Possible Causes
RADIO AMPLIFIER
  1. When Monitored: Continuously.
  1. Set Condition: Whenever the CAN B Bus (+) or B Bus (-) circuit is open, shorted to voltage or shorted to ground, this code will set.
Possible Causes
CAN B BUS DTCs IN THE TOTALLY INTEGRATED POWER MODULE (TIPM)
(D54) CAN B BUS (-) CIRCUIT OPEN
(D55) CAN B BUS (+) CIRCUIT OPEN
AMPLIFIER
  1. When Monitored: Continuously when the ignition is on. The battery voltage between 10.0 and 16.0 Volts. Ignition Off Draw (IOD) fuse installed. Totally Integrated Power Module (TIPM) is configured correctly.
  1. Set Condition: Bus messages not received from the Totally Integrated Power Module (TIPM) for approximately two to five seconds.
Possible Causes
CAN BUS CIRCUITS OPEN OR SHORTED
DTCS RELATED TO BATTERY VOLTAGE, IGNITION, OR VIN MESSAGES
TOTALLY INTEGRATED POWER MODULE POWER AND GROUND
TIPM NOT CONFIGURED CORRECTLY
TOTALLY INTEGRATED POWER MODULE (TIPM)
MODULE THAT SET THIS DTC
  1. When Monitored: Continuously when the ignition is on. Battery voltage between 10 and 16 volts. Ignition Off Draw (IOD) fused installed. Totally Integrated Power Module (TIPM) is configured correctly.
  1. Set Condition: Bus messages not received from the Radio for approximately two to five seconds.
Possible Causes
CAN BUS CIRCUITS OPEN OR SHORTED
DTCS RELATED TO BATTERY VOLTAGE, IGNITION, OR VIN MESSAGES
RADIO POWER AND GROUND
TIPM NOT CONFIGURED CORRECTLY
RADIO
MODULE THAT SET THIS DTC

More articles — Audio System (Amplifier) - Electrical Diagnostics