Home ReviewsRefund
Home/Chevrolet/Silverado 3500 HD/Chevrolet Silverado 3500 HD (2007-2012)/Repair manual/Automatic Trans/Shift Interlock System: Other
Contents Wiring diagrams Section: Automatic Trans All sections

Shift Interlock System: Other Chevrolet Silverado 3500 HD

Automatic Trans ~385 words

Reference Information

Schematic Reference

Shift Lock Control Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Automatic Transmission Shift Lock Control Description and Operation

Electrical Information Reference

  1. «Circuit Testing»(ref-317172-S12100958872009060900000)
  2. «Connector Repairs»(ref-317172-S41839496312009060900000)
  3. «Testing for Intermittent Conditions and Poor Connections»(ref-317172-S08096213032009060900000)
  4. «Wiring Repairs»(ref-317172-S40815672902009060900000)

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

  1. Ignition ON, clear the DTC. Observe the scan tool BCM Stop Lamp Relay Command parameter while pressing and releasing the brake pedal. The parameter should change between ON and OFF. If the parameter does not change between the specified values, refer to «Stop Lamps Malfunction»(ref-317143-S16667232192009060900000) .
  2. Press the brake pedal, the vehicle operator should be able to move the shifter out of the PARK position.

Repair Procedures

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

  1. «Automatic Transmission Shift Lock Control Actuator Replacement»(ref-317218-S14925089412009060900000)
  2. «Control Module References»(ref-317173-S10180079792009060900000) for BCM replacement, setup, and programming

Symptoms - Automatic Transmission Shift Lock Control

IMPORTANTThe following steps must be completed before using the symptom tables.
  1. Perform the «Diagnostic System Check - Vehicle»(ref-317170-S03444519162009060900000) before using the Symptom Tables in order to verify that all of the following are true: There are no DTCs set. The control modules can communicate via the serial data link.
  2. Review the system operation in order to familiarize yourself with the system functions. Refer to «Automatic Transmission Shift Lock Control Description and Operation»(ref-317218-S19819738482009060900000) .

Intermittent

Faulty electrical connections or wiring may be the cause of intermittent conditions. Refer to Testing for Intermittent Conditions and Poor Connections

Schematic Reference

Shift Lock Control Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Automatic Transmission Shift Lock Control Description and Operation

Electrical Information Reference

  1. «Circuit Testing»(ref-317172-S12100958872009060900000)
  2. «Connector Repairs»(ref-317172-S41839496312009060900000)
  3. «Testing for Intermittent Conditions and Poor Connections»(ref-317172-S08096213032009060900000)
  4. «Wiring Repairs»(ref-317172-S40815672902009060900000)

Scan Tool Reference

Control Module References for scan tool information

  1. Ignition ON, clear the DTC. Observe the scan tool BCM Stop Lamp Relay Command parameter while pressing and releasing the brake pedal. The parameter should change between ON and OFF. If the parameter does not change between the specified values, refer to «Stop Lamps Malfunction»(ref-317143-S16667232192009060900000) .
  2. Press the brake pedal, the vehicle operator should be able to move the shifter out of the PARK position.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

  1. «Automatic Transmission Shift Lock Control Actuator Replacement»(ref-317218-S14925089412009060900000)
  2. «Control Module References»(ref-317173-S10180079792009060900000) for BCM replacement, setup and programming

More articles — Shift Interlock System