Contents Wiring diagrams Section: Automatic HVAC System All sections

Heating, Ventilation and Air Conditioning: Specifications Chevrolet Silverado 3500 HD

Fastener Tightening Specifications

ApplicationSpecification
MetricEnglish
A/C High Pressure Recirculation Switch6 N.m53 lb in
A/C Low Pressure Switch6 N.m53 lb in
A/C Refrigerant Filter Retaining Nuts15 N.m11 lb ft
Accumulator Bracket Nut9 N.m80 lb in
Accumulator Clamp Bolt10 N.m8 lb ft
Air Distribution Duct Screws1.6 N.m14 lb in
Air Outlet Mounting Screw1.6 N.m14 lb in
Auxiliary A/C Tubes at the Auxiliary HVAC Module16 N.m12 lb ft
Auxiliary Evaporator Tube to TXV Nut28 N.m21 lb ft
Auxiliary HVAC Module A/C Line Nut16 N.m12 lb ft
Auxiliary HVAC Module Mounting Nuts to Vehicle9 N.m80 lb in
Blower Motor Insulating Cover Screw1.6 N.m14 lb in
Blower Motor Relay/Resistor Screw1.6 N.m14 lb in
Compressor Bracket Mounting Bolts50 N.m37 lb ft
Compressor Clutch Coil Connector Retaining Bracket Screw9 N.m80 lb in
Compressor Clutch Plate Retaining Bolt18 N.m13 lb ft
Compressor Discharge Hose Nut at Compressor16 N.m12 lb ft
Compressor Hose Bolt to Compressor (L18 Harrison)34 N.m25 lb ft
Compressor Mounting Bolts (L18 Harrison)50 N.m37 lb ft
Compressor Mounting Bolts (LR4, LM7, LQ4 Denso)50 N.m37 lb ft
Compressor Suction/Discharge Hose Bolt34 N.m25 lb ft
Compressor Suction Hose Nut to Accumulator16 N.m12 lb ft
Compressor Suction Hose to Accumulator41 N.m30 lb ft
Condenser Upper Insulator Retainer Bolts2.4 N.m21 lb in
Discharge Hose Mounting Bolt (LR4, LM7, LQ4 Denso)16 N.m12 lb ft
Evaporator Tube Fitting at Orifice25 N.m18 lb ft
Evaporator Tube Nut at Condenser16 N.m12 lb ft
Evaporator Tube Nut at Evaporator16 N.m12 lb ft
Evaporator Tube to the Auxiliary A/C Tube16 N.m12 lb ft
Filter Access Door Screw1.6 N.m14 lb in
Floor Air Outlet Duct Screw1.6 N.m14 lb in
Heater A/C Auxiliary Tubes Retaining Nuts7 N.m62 lb in
Heater Core Cover Screws1.6 N.m14 lb in
Heater Hose Outlet Mounting Nut and Bolt25 N.m18 lb ft
Heater/Ventilation Module Mounting Nuts9 N.m80 lb in
Heater/Ventilation Module Mounting Screws4 N.m35 lb in
Heater Ventilation Module Screws1.6 N.m14 lb in
Insulator Retainers and Bolts2.4 N.m21 lb in
Pressure Relief Valve9 N.m80 lb in
Suction Hose Mounting Bolt (LR4, LM7, LQ4 Denso)16 N.m12 lb ft

Refrigerant System Capacities (Non-HP2)

ApplicationSpecification
MetricEnglish
PAG Oil GM P/N 12378526 for United States PAG Oil GM P/N 88900060 for Canada
Accumulator Replacement60 ml*2 oz.*
* Add PAG oil equal to the amount of oil drained from the accumulator plus the specified additional amount.
Compressor Replacement60 ml 12 oz. 1
The Denso service compressor is precharged with 237 ml (8.0 oz.) of PAG oil.
Condenser Replacement30 ml 11 oz. 1
Evaporator Replacement90 ml 13 oz. 1
Evaporator, Rear Replacement90 ml 13 oz. 1
Total System PAG Oil Capacity210 ml7.1 oz.
Total System PAG Oil Capacity with Rear A/C330 ml11 oz.
R-134a
Refrigerant Charge0.7 kg1.6 lb
Refrigerant Charge Utility with Front and Rear A/C1.13 kg2.5 lb
Refrigerant Charge Suburban with Front and Rear A/C1.4 kg3.0 lb
1 If more than the specified amount of PAG oil was drained from a component, add the equal amount of oil drained.

Begin the system diagnosis with Diagnostic System Check - Vehicle . The Diagnostic System Check - Vehicle will provide the following information

  1. The identification of the control modules which are not communicating.
  2. The identification of any stored diagnostic trouble codes (DTCs) and their status.

The use of the Diagnostic System Check - Vehicle will identify the correct procedures to begin vehicle diagnosis. These must be performed before system DTC or symptom diagnosis.