Object Detection System and Pedestrian Protection System: Other Chevrolet Captiva I facelift 2

Conditions for Clearing

1. The DTC will transition to history when the fault is no longer present.
2. A history DTC will clear after 100 malfunction-free ignition cycles.

Reference Information

Schematic Reference

Object Detection Schematics

Connector End View Reference

COMPONENT CONNECTOR END VIEWS - INDEX

Description and Operation

Object Detection Description and Operation

Electrical Information Reference

1. «Circuit Testing»(ref-611726-S06194601762014042500000)
2. «Connector Repairs»(ref-611726-S00196769002014042500000)
3. «Testing for Intermittent Conditions and Poor Connections»(ref-611726-S02524567402014042500000)
4. «Wiring Repairs»(ref-611726-S39691427742014042500000)

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Control Module References for BCM replacement, setup and programming

Schematic Reference

Object Detection Schematics

Connector End View Reference

COMPONENT CONNECTOR END VIEWS - INDEX

Description and Operation

Object Detection Description and Operation

Electrical Information Reference

1. «Circuit Testing»(ref-611726-S06194601762014042500000)
2. «Connector Repairs»(ref-611726-S00196769002014042500000)
3. «Testing for Intermittent Conditions and Poor Connections»(ref-611726-S02524567402014042500000)
4. «Wiring Repairs»(ref-611726-S39691427742014042500000)

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

1. Ignition ON.
2. Verify that DTC B1405 is not set. If the DTC is set Refer to «DTC B1405»(ref-611758-S42708320532014042500000) If the DTC is not set
3. Verify that DTC B0958 01, B0959 01, B0960 01, B0961 01, B0958 21, B0959 21, B0960 21 or B0961 21 is not set. If the DTC is set Check the B78 Rear Object Sensor for contamination with snow, mud, dirt, slush or ice. If contaminated, clean sensor. If there is no contamination Refer to Circuit/System Testing. If the DTC is not set
4. Verify that DTC B0958 3A, B0959 3A, B0960 3A or B0961 3A is not set. If the DTC is set Replace the B78 Rear Object Sensor with the correct sensor type.
5. Ignition ON, engine running, transmission in REVERSE.
6. Verify the scan tool Parking Assist System Status parameter displays Enabled. If the Parking Assist System displays Disabled Refer to Circuit/System Testing. If the Parking Assist System displays Enabled
7. All OK.

Perform the Diagnostic Repair Verification after completing the repair.

1. «Rear Parking Assist Alarm Sensor Replacement»(ref-611758-S38006040622014042500000)
2. «Control Module References»(ref-611721-S33225353212014042500000) for parking assist control module replacement, programming and setup

Schematic Reference

Object Detection Schematics

Connector End View Reference

COMPONENT CONNECTOR END VIEWS - INDEX

Description and Operation

Object Detection Description and Operation

Electrical Information Reference

1. «Circuit Testing»(ref-611726-S06194601762014042500000)
2. «Connector Repairs»(ref-611726-S00196769002014042500000)
3. «Testing for Intermittent Conditions and Poor Connections»(ref-611726-S02524567402014042500000)
4. «Wiring Repairs»(ref-611726-S39691427742014042500000)

Scan Tool Reference

Control Module References for scan tool information

1. Ignition ON.
2. Verify the DTC B1015 is not. If the DTC B1015 is set Program the control module the DTC originally set in. Verify the DTC does not set. If the DTC is sets, replace the control module the DTC set in. If the DTC does not set All OK If the DTC B1015 is not set
3. All OK

Perform the Diagnostic Repair Verification after completing the repair

Control Module References for the parking assist control module, frontview camera module replacement, programming and setup.

Schematic Reference

Object Detection Schematics

Connector End View Reference

COMPONENT CONNECTOR END VIEWS - INDEX

Description and Operation

Object Detection Description and Operation

Electrical Information Reference

1. «Circuit Testing»(ref-611726-S06194601762014042500000)
2. «Connector Repairs»(ref-611726-S00196769002014042500000)
3. «Testing for Intermittent Conditions and Poor Connections»(ref-611726-S02524567402014042500000)
4. «Wiring Repairs»(ref-611726-S39691427742014042500000)

Scan Tool Reference

Control Module References for scan tool information

1. Ignition ON, engine running, transmission in R.
2. Verify the scan tool Park Assist Sensor Reference Voltage parameter is between 7.2-9.2 V. If Park Assist Sensor Reference Voltage is not between 7.2-9.2 V Refer to Circuit/System Testing If Park Assist Sensor Reference Voltage is between 7.2-9.2 V
3. All OK.

Perform the Diagnostic Repair Verification after completing the repair.

Control Module References for rear parking assist control module replacement, programming and setup.

Symptoms - Object Detection

Note. Review the system operation in order to familiarize yourself with the system functions. Refer to Object Detection Description and Operation .

Intermittent

Faulty electrical connections or wiring may be the cause of intermittent conditions. Refer to Testing for Intermittent Conditions and Poor Connections .

Schematic Reference

Object Detection Schematics

Connector End View Reference

COMPONENT CONNECTOR END VIEWS - INDEX

Description and Operation

Object Detection Description and Operation

Electrical Information Reference

1. «Circuit Testing»(ref-611726-S06194601762014042500000)
2. «Connector Repairs»(ref-611726-S00196769002014042500000)
3. «Testing for Intermittent Conditions and Poor Connections»(ref-611726-S02524567402014042500000)
4. «Wiring Repairs»(ref-611726-S39691427742014042500000)

Scan Tool Reference

Control Module References for scan tool information

Perform the Diagnostic Repair Verification after completing the repair.

Control Module References for rear parking assist module replacement, programming and setup.

Schematic Reference

Object Detection Schematics

Connector End View Reference

COMPONENT CONNECTOR END VIEWS - INDEX

Description and Operation

Object Detection Description and Operation

Electrical Information Reference

1. «Circuit Testing»(ref-611726-S06194601762014042500000)
2. «Connector Repairs»(ref-611726-S00196769002014042500000)
3. «Testing for Intermittent Conditions and Poor Connections»(ref-611726-S02524567402014042500000)
4. «Wiring Repairs»(ref-611726-S39691427742014042500000)

1. Inspect the rearview camera and verify there are no debris on the lens and that the bezel or bezel seal is not damaged. If debris are found on the lens, clean the lens. If the lens, bezel or bezel seal are damaged, replace as necessary.
2. Engine running, vehicle in PARK, verify the backup lamps are off. If the backup lamps are illuminated, refer to Rearview Camera System Always On.
3. Vehicle in REVERSE, verify a clear rear vision image is displayed on the inside rearview mirror. If a clear image is not displayed, refer to Rearview Camera System Does Not Display.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

1. «Rearview Driver Information Camera Replacement»(ref-611758-S22489306282014042500000)
2. «Control Module References»(ref-611721-S33225353212014042500000) for inside rearview mirror replacement, setup and programming

Scheme 5

Rear Object Alarm Control Module Replacement