Repair manual
Wiring diagrams
Cadillac SRX I Repair Manual
Step-by-step repair and maintenance instructions for the Cadillac SRX I (2003–2009): removal, installation, adjustment, diagnostics and parameter checks with illustrations.
- Fastener Tightening Specifications
- Engine Mechanical Specifications
- Sealers, Adhesives, and Lubricants
- Vehicle Identification Number
- Engine Traceability Label
- Engine Verification Label
- Diagnostic Starting Point - Engine Mechanical
- Strategy Based Diagnostics
- Visual/Physical Inspection
- Intermittent
- Symptom List
- Base Engine Misfire without Internal Engine Noises
- Base Engine Misfire with Abnormal Internal Lower Engine Noises
- Base Engine Misfire with Abnormal Valve Train Noise
- Base Engine Misfire with Coolant Consumption
- Base Engine Misfire with Excessive Oil Consumption
- Engine Noise on Start-Up, but Only Lasting a Few Seconds
- Upper Engine Noise, Regardless of Engine Speed
- Lower Engine Noise, Regardless of Engine Speed
- Engine Noise Under Load
- Engine Will Not Crank - Crankshaft Will Not Rotate
- Coolant in Combustion Chamber
- Coolant in Engine Oil
- Tools Required
- Cylinder Leakage Test
- Oil Consumption Diagnosis
- Oil Pressure Diagnosis and Testing
- Oil Leak Diagnosis
- Crankcase Ventilation (CV) System Inspection
- Results of Incorrect Operation
- Diagnostic Aids
- Test Description
- Drive Belt Tensioner Diagnosis
- Drive Belt System Description
- Engine Component Description
- Crankcase
- Crankshaft
- Connecting Rods and Pistons
- Camshaft Drive System
- Camshaft Position Actuator System
- Cylinder Heads
- Induction System
- Right and Left Bank Designation
- New Product Information
- Torque Values and/or Fastener Tightening Strategies
- Changed Engine Specifications
- New Sealants and/or Adhesives
- Disassembly and Assembly Procedure Revisions
- Engine Mechanical Diagnostic Procedure Revisions
- New Special Tools Required
- A Component Comparison from the Previous Year
- Lubrication Description
- Cleanliness and Care
- Separating Parts
- Gasket Reuse and Applying Sealant
- Separating Components
- Cleaning Gasket Surfaces
- Assembling Components
- Sealant Types
- Anaerobic Type Room Temperature Vulcanizing (RTV) Sealant
- Anaerobic Type Gasket Eliminator Sealant
- Anaerobic Type Threadlock Sealant
- Anaerobic Type Pipe Sealant
- Tools and Equipment
- Special Tools
- Fastener Tightening Specifications
- Utility/Van Zoning
- Electrical Symbols
- Basic Knowledge Required
- Checking Aftermarket Accessories
- Circuit Testing
- Using Connector Test Adapters
- Probing Electrical Connectors
- Frontprobe
- Backprobe
- Troubleshooting with a Digital Multimeter
- Troubleshooting with a Test Lamp
- Using Fused Jumper Wires
- Measuring Voltage
- Measuring Voltage Drop
- Measuring Frequency
- Testing for Continuity
- With a DMM
- With a Test Lamp
- Testing for Short to Ground
- Fuse Powering Several Loads
- Testing for a Short to Voltage
- Testing for Intermittent Conditions and Poor Connections
- Testing for Proper Terminal Contact
- Round Wire Connectors
- Flat Wire (Dock and Lock) Connectors
- Inducing Intermittent Fault Conditions
- Salt Water Spray
- High Temperature Conditions
- Low Temperature Conditions
- Testing for Electrical Intermittents
- Scan Tool Snapshot Procedure
- Circuit Protection - Circuit Breakers
- Circuit Protection - Fusible Links
- Repairing a Fusible Link
- Wiring Repairs
- Repairing Damaged Wire Insulation
- Flat Wire Repairs
- GMLAN Wiring Repairs
- GMLAN Repairs
- GMLAN Connector Terminal Repair
- GMLAN Wire Repair
- Heated Oxygen Sensor (HO2S) Wiring Repairs
- Splicing Copper Wire Using Splice Clips
- Splicing Copper Wire Using Splice Sleeves
- Splicing Twisted or Shielded Cable
- Splicing Inline Harness Diodes
- SIR/SRS Wiring Repairs
- SIR/SRS Connector Repair (Plastic Body and Terminal Metal Pin)
- SIR/SRS Wire Pigtail Repair
- SIR/SRS Wire Repair
- SIR/SRS System Wire Splice Repair
- Connector Position Assurance (CPA)
- Terminal Position Assurance (TPA)
- Connector Repairs
- Connector Position Assurance Locks
- Terminal Position Assurance Locks
- Terminal Removal
- Terminal Repair
- Reinstalling Terminal
- Terminal Installation
- Weather Pack Connectors
- Tools Required
- Removal Procedure
- Repair Procedure
- Replacement Procedure
- Terminal Repair Procedure
- Repairing Connector Terminals
- Power and Grounding Schematic Icons
- Installation Procedure
- Special Tools