Note. Check for any applicable Technical Service Bulletins (TSB) that may apply.
| Application | Ft. Lbs. (N.m) |
|---|
| Balance Shaft Gear Bolt (1) |
| Step 1 | 16 (22) |
| Step 2 | Additional 70 Degrees |
| Balance Shaft Retainer Bolt | 22 (30) |
| Camshaft Sprocket Bolt |
| Step 1 | 74 (100) |
| Step 2 | Additional 90 Degrees |
| Connecting Rod Bolt |
| Step 1 | 20 (27) |
| Step 2 | Additional 50 Degrees |
| Crankshaft Pulley/Balancer Bolt |
| Step 1 | 110 (150) |
| Step 2 | Additional 76 Degrees |
| Cylinder Head Bolts (2) |
| Step 1 | 37 (50) |
| Step 2 | Additional 130 Degrees |
| Step 3 (4 Center Bolts) | Additional 30 Degrees |
| Drive Bolt Tensioner Bracket Bolt (VIN 1) | 37 (50) |
| EGR Valve Adaptor Nut | 37 (50) |
| Exhaust Manifold Bolt | 22 (30) |
| Flywheel Bolt |
| Step 1 | 11 (15) |
| Step 2 | Additional 50 Degrees |
| Front Cover Bolt |
| Step 1 | (3) 11 (15) |
| Step 2 | Additional 30 Degrees |
| Fuel Feed & Return Line Fitting | 22 (30) |
| Intake Manifold Bolts |
| VIN 1 |
| Lower | (1) (4) 11 (15) |
| Upper (Supercharger) | 17 (23) |
| VIN K (All Except "F" Body) |
| Lower | (1) (4) 11 (15) |
| Upper | (5) |
| VIN K ("F" Body) |
| Lower | (1) (6) 11 (15) |
| Upper | (7) |
| Knock Sensor | 14 (19) |
| Main Bearing Cap Bolt (8) |
| Step 1 | 30 (40) |
| Step 2 | Additional 110 Degrees |
| Oil Cooler Adapter Connector | 37 (50) |
| Oil Filter Adapter-To-Front Cover Bolt | 22 (30) |
| Oil Pan Bolt | (1) 10 (14) |
| Oil Screen-To-Block Bolt | 11 (15) |
| Rocker Arm Bolt (1) |
| Step 1 | 11 (15) |
| Step 2 | Additional 90 Degrees |
| Side Main Bearing Cap Bolt |
| Step 1 | 11 (15) |
| Step 2 | Additional 45 Degrees |
| Supercharger-To-Lower Intake Manifold Bolt (VIN 1) | 17 (23) |
| Thermostat Housing Bolts | 15 (20) |
| Timing Chain Damper Bolt (Special Bolt) | 16 (22) |
| Torque Axis Engine Mount Bracket Front Nuts | 52 (70) |
| Torque Axis Engine Mount Bracket Rear Nut | 22 (30) |
| Valve Lifter Guide Bolt | 22 (30) |
| Water Pump Bolts |
| Long Bolts |
| Step 1 | 15 (20) |
| Step 2 | Additional 40 Degrees |
| Short Bolts |
| Step 1 | 11 (15) |
| Step 2 | Additional 80 Degrees |
| INCH Lbs. (N.m) |
| Oil Pump Cover Bolt | 97 (11) |
| Rocker Arm Cover Bolt | (1) 88 (10) |
| Throttle Body Nut | 89 (10) |
| (1) Apply thread locking compound to bolt(s). (2) Tighten bolts in sequence. (Схема №6) (3) Apply thread sealant to bolt(s). (4) Tighten bolts in sequence. (Схема №5) (5) Tighten bolts in sequence to 89 INCH lbs. (10 N.m). (Схема №3) (6) Tighten bolts in sequence. (Схема №4) (7) Tighten the vertical bolts in sequence to 11 ft. lbs. (15 N.m). Tighten the water outlet bolts in sequence to 20 ft. lbs. (27 N.m). Tighten the side bolts in sequence to 22 ft. lbs. (30 N.m). (Схема №2) (8) Refer to tightening procedure. See CRANKSHAFT & MAIN BEARINGS. |
| (1) | Apply thread locking compound to bolt(s). |
| (2) | Tighten bolts in sequence. (Схема №6) |
| (3) | Apply thread sealant to bolt(s). |
| (4) | Tighten bolts in sequence. (Схема №5) |
| (5) | Tighten bolts in sequence to 89 INCH lbs. (10 N.m). (Схема №3) |
| (6) | Tighten bolts in sequence. (Схема №4) |
| (7) | Tighten the vertical bolts in sequence to 11 ft. lbs. (15 N.m). Tighten the water outlet bolts in sequence to 20 ft. lbs. (27 N.m). Tighten the side bolts in sequence to 22 ft. lbs. (30 N.m). (Схема №2) |
| (8) | Refer to tightening procedure. See CRANKSHAFT & MAIN BEARINGS . |
