Oil Capacity
Oil change amount including filter is 8.0 qts. (7.5L).
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) |
|---|
| Camshaft Bearing Cap Bolts | 11 (15) |
| Camshaft Sprocket Bolts | 11 (15) |
| Clutch Drive Plate | 17 (23) |
| Connecting Rod Bolts (1) |
| Step 1 | 15 (20) |
| Step 2 | Additional 80 Degrees |
| Cooling Fan Nut | (2) 22 (30) |
| Cylinder Head Bolt (3) |
| Step 1 | 22 (30) |
| Step 2 | Additional 80 Degrees |
| Step 3 | Additional 80 Degrees |
| Exhaust Manifold Bolts | 18 (24) |
| Flywheel-To-Crankshaft Bolts | 78 (105) |
| Front/Rear Crankshaft End Cover Bolts (8-mm) | 16 (22) |
| Idler Sprocket Flange Nuts | 10 (13) |
| Intake Manifold Bolts | 11 (15) |
| Main Bearing Cap Bolts (1) |
| Step 1 | 15 (20) |
| Step 2 (Torque Angle) | 70 Degrees |
| Main Bearing Sleeve Bolts (4) |
| Step 1 | 15 (20) |
| Step 2 (Torque Angle) | 45 Degrees |
| Oil Filter Cover | 20-24 (27-33) |
| Oil Pan Cover Bolts (8-mm) | 15 (20) |
| Oil Pump Hexagonal Sleeve | (5) |
| Oil Pump Hexagonal Sleeve Bolt | 16 (22) |
| Oil Pump Sprocket Nut | 33 (48) |
| Starter Bolts | 37 (50) |
| Upper/Lower Timing Chain Cover Bolts (8-mm) | 16 (22) |
| Vibration Damper Bolts (7-mm) | 17 (23) |
| Vibration Damper Hub Bolt (1) |
| Step 1 | 66-81 (90-110) |
| Step 2 | 60 Degrees |
| Step 3 | 60 Degrees |
| Step 4 | 30 Degrees |
| Water Pump Bolts (8-mm) | 16 (22) |
| INCH Lbs. (N.m) |
| Cylinder Head Cover Bolts | 89 (10) |
| Front/Rear Crankshaft End Cover Bolts (6-mm) | 89 (10) |
| Fuel Injectors-To-Intake Bolts | 89 (10) |
| Main Bearing Sleeve Nuts | 89 (10) |
| Oil Filter Housing Bolts | 89 (10) |
| Oil Pan Cover Bolts (6-mm) | 89 (10) |
| Timing Chain Adjusting Bracket | 12 (1.3) |
| Upper/Lower Timing Case Cover Bolts (6-mm) | 89 (10) |
| Water Pump Bolts (6-mm) | 89 (10) |
| Water Pump Pulley Bolts | 89 (10) |
| (1) Use NEW bolts. (2) Specification applies using BMW 32-mm Wrench (11-5-040). If using conventional wrench, tighten nut to 29 ft. lbs. (40 N.m). (3) Use NEW, lightly oiled bolts, and tighten crosswise from middle of cylinder head to outside. (4) (Схема №19)and (Схема №20). (5) Use to adjust oil pump chain deflection. See OIL PUMP under ENGINE OILING. |
| (2) | Specification applies using BMW 32-mm Wrench (11-5-040). If using conventional wrench, tighten nut to 29 ft. lbs. (40 N.m). |
| (3) | Use NEW, lightly oiled bolts, and tighten crosswise from middle of cylinder head to outside. |
| (4) | (Схема №19)and (Схема №20). |
| (5) | Use to adjust oil pump chain deflection. See OIL PUMP under ENGINE OILING. |
ENGINE SPECIFICATIONS
| Application | Specification |
|---|
| 4.4L |
| Displacement | 268 Cu. In. (4.4L) |
| Bore | 3.60" (92.0 mm) |
| Stroke | 3.25" (82.7 mm) |
| Compression Pressure | (1) |
| Compression Ratio | 10.0:1 |
| Fuel System | SFI |
| Horsepower @ RPM | 282 @ 5700 |
| Torque Ft. Lbs. @ RPM | 310 @ 3900 |
| (1) Information is not available from manufacturer. |
| (1) | Information is not available from manufacturer. |
