Home/Audi/A8/Audi A8 D3 рестайлинг (2005-2007)/Repair manual/6.0l 12-cyl. 4v Generic Scan Tool, Engine Code(s): Bsb/Technical Data

Contents

Section: 6.0l 12-cyl. 4v Generic Scan Tool, Engine Code(s): Bsb

Safety Precautions

Clean Working Conditions

Fuel Supply System Components, Removing and Installing

Fuel Tank With Attachments

Fuel Tank, Draining

Fuel Pumps, Checking

EVAP System

Function of Leak Diagnostic

EVAP Canister, Removing and Installing

EVAP System, Checking for Proper Seal

EVAP Canister Purge Regulator Valve 2, Checking

Right instrument panel fuse holder

Check wires to control module

EVAP Canister Purge Solenoid Valve, Removing and Installing

Electronic Power Control

Electronic Power Control Components, Servicing

Accelerator Pedal Module with Throttle Position Sensors, Removing and Installing

Throttle Position Sensor, Checking

Checking voltage supply

Fuel Injection System, Servicing

Technical Data

Component Locations

Intake Manifold, Disassembling and Assembling

Fuel Rail with Injectors, Disassembling and Assembling

Engine Components, Checking

Oxygen Sensor Heaters Before Catalytic Converter, Checking

Oxygen Sensor Heaters After Catalytic Converter, Checking

Mass Air Flow Sensor, Checking

Throttle Valve Control Modules, Checking

Coolant Temperature Sensor, Checking

Intake Air Temperature Sensor, Checking

Engine Speed Sensor, Checking

Engine Coolant Temperature Sensor on Radiator, Checking

MAP Controlled Thermostat, Checking

Intake System, Checking for Leaks

Coolant Fan Control Modules, Checking

Fuel Injectors, Checking

Checking wires to Engine Control Module (ECM)

Fuel Injectors, Checking Injection Quantity and Seal

Fuel Pressure Regulator and Residual Pressure, Checking

Functions, Checking

Oxygen Sensors and Oxygen Sensor Regulation Before Catalytic Converter, Checking

Oxygen Sensors and Oxygen Sensor Regulation after Catalytic Converter, Checking

Checking oxygen sensor wires to control module

Engine Control Modules, Replacing

Additional Signals, Checking

Speed Signal, Checking

Checking wiring

Exhaust System Components, Removing and Installing

Three Way Catalytic Converters, Checking

Secondary Air Injection System

Secondary Air Injection, Component Overview

Secondary Air Injection Combination Valve, Checking

Secondary Air Injection, Left Combination Valve, Removing and Installing

Secondary Air Injection, Right Combination Valve, Removing and Installing

Secondary Air Injection Solenoid Valves, Checking

Secondary Air Injection Pump Motors, Checking

Combination Valves, Checking

Ignition System, Servicing

Ignition System Components, Removing and Installing

Cylinder bank 1

Cylinder bank 2

Technical Data, Spark Plugs

Ignition Coils With Power Output Stage, Removing and Installing

Ignition Coils With Power Output Stages, Checking

Check activation

Terminal Resistance for CAN-Bus, Checking

Camshaft Position Sensor, Checking

Knock Sensors, Checking

Camshaft Adjustment Valves, Checking

Transmission Regulating Electrical Components, Checking

TCM Voltage Supply, Checking

Transmission Control Module, Replacing

OBD, General Information

On Board Diagnostic Technical Data

Selectable Diagnostic Modes

Diagnostic Tester, Connecting

Diagnostic Mode, Selecting

Address Word 33 - On-Board Diagnostic

Diagnostic Mode 01 - Read Current System Data

Diagnostic Mode 03 - Read DTC Memory

SAE Diagnostic Trouble Codes

Diagnostic Mode 04 - Erase DTC Memory

Diagnostic Mode 05 - Read Oxygen Sensor Monitoring Test Results

Evaluation Test 07 - Minimum Voltage At Sensor for Test Cycle

Evaluation Test 08 - Maximum Voltage At Sensor for Test Cycle

Evaluation Test 129 - Oxygen Sensor Value

Evaluation Test-Id 130 - Control Barrier Value

Evaluation Test 131 - Dynamic Value

Diagnostic Mode 6 - Checking Test Results of Components Not Continuously Monitored

Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions

Test 01 - Catalytic Converter

Evaluation test-ID 01: Catalytic converter monitoring

Test 03 - Secondary Air Injection System

Evaluation test-ID 03: Secondary air injection (AIR) system

Test 05 - Tank Ventilation System

Evaluation test-ID 05: Tank ventilation system

Test 09 - Engine Coolant Temperature Sensor

Evaluation test-ID 09: Engine Coolant Temperature (ECT) Sensor G62

Diagnostic Mode 07 - Read Faults Detected During the Current or Last Driving Cycle

Diagnostic Mode 08 - Request Control of On-Board System, Test or Component

Diagnostic Mode 09 - Read Vehicle Information

Readiness Code

Readiness Code, Reading

Readiness Code, Generating

DTC Tables

Fuel and Air Metering and Auxiliary Emission Controls

Fuel and Air Metering

Ignition System

Auxiliary Emission Controls

Speed and Idle Control

Control Module and Auxiliary Outputs

Transmission

Control Modules, Input and Output Signals

Network, Electrical

Network, Communication

Network, Software

Network, Data

All sections

Technical Data Audi A8 D3 рестайлинг

6.0l 12-cyl. 4v Generic Scan Tool, Engine Code(s): Bsb

Technical Data

Engine code				BAS
Engine idle speed 1			RPM	600 to 800
Engine Control Modules (ECM) 2
		System designation		Motronic ME7.1.1
		Terminals on Engine Control Module (ECM)		121
		Replacement part number
		Engine speed (RPM) limitation	RPM	From approx. 6500