Home/Audi/A8/Audi A8 D3 рестайлинг 2 (2007-2010)/Repair manual/Maintenance Procedures/Wiper blade, replacing

Contents

Section: Maintenance Procedures

Engine overview

Delivery inspection

Oil change service

Inspection service

Contact corrosion

All switches, all electrical components, all displays and other operating elements: Checking function

Final drive (automatic transmission): Check oil level, add oil if necessary

Wheel bolts

Correct wheel installation

Battery manager: Deactivate transport mode

Battery with magic eye

Battery sealing plugs

Battery, disconnecting and connecting

Battery level, read out with Guided Fault Finding

Brake system: Visual inspection for leaks and damage

Tires, checking

Checking tire wear pattern

Check tread depth

Spare wheel

Brake pads: Thickness, checking

Brake fluid level, dependent on lining wear: Check

Brake fluid, changing

Table - Sequence / quantity of brake fluid

Digital TV Tuner: Assign remote control key fob

Vehicle level, adjusting

DTC memory, interrogating with VAS 5051/ 5052

Check vehicle key function

Noise insulation, removing

Front axle joints: Seal boots, checking play and attachment

Power steering: Check for leaks and fluid level, top off Power steering fluid, if necessary

Rear lid hinges: Lubricate

Telephone/Telematics control module, initializing

A/C system: Check function, set temperature to 72 F (22 C)

Cooling system: Check freeze protection, add coolant, if necessary

Ribbed belt, W12 (6.0 MPI) and 10-cylinder gasoline engines (5.2 FSI), checking

Ribbed belt, removing and installing

Instrument cluster: Adapt language version

8-cyl. gasoline engines

10-cyl. gasoline engines (5.2 FSI)

W12 gasoline engine

Engine cover, removing

Engine (from above and below) and engine compartment: Visual inspection for leaks and damage

Engine oil: drain, replace oil filter

V8 5-valve gasoline engines

10-cyl. gasoline engine (5.2 FSI)

Engine oil: Fill

Engine: Oil level, checking

Navigation: Eject button, unlocking

Test drive: Perform

Headlamp washer system: Check spray jet setting.

Windshield spray jet setting

Windshield wiper blades: Park position and checking for damage

Wiper blade, replacing

Sunroof: Check function, clean guide rails and spray on grease spray

Windshield/headlamp wiper system: Filling with fluid

Headlamps: Check setting, adjust if necessary

Check and adjustment conditions

Tank filling table

Headlamps, checking adjustment (with new test screen without 15 ° setting line)

Ellipsoid headlamps, adjusting

Headlamps, adjusting (gas-discharge lamps)

Special tools and equipment needed

Plenum chamber water drain, checking and cleaning

Service display, resetting

Oil quality, adapting

Maximum values, adapting

Telematics: Emergency battery, replacing

Underbody protection: Visual inspection for damage

Transport mode, deactivating

Winter tires from factory

Timing belt: replacing (V8 gasoline engines)

Clock, setting

V8 gasoline engines

V10 gasoline engines

Headlights: Aiming using Hella Universal Beamsetter IV

Type plate / Vehicle Identification Number (VIN)

Vehicle, lifting

Suspension blocks, installing

Tow starting/towing Some engines listed below are for European models and are not applicable to the North American market.

Vehicle checks within inspection and service framework

All sections

Wiper blade, replacing Audi A8 D3 рестайлинг 2

Maintenance Procedures 2 illustrations

Wiper blade, replacing

Removing

Lift wiper arm off of windshield.

Scheme 62

Scheme 62

Scheme 62

Slide retaining clip - 2 - in direction of - arrow - from wiper arm - 3 -.
Remove wiper blade - 1 - down off wiper arm.

Installing

Scheme 63

Scheme 63

Scheme 63

Insert wiper arm joint in guide on wiper blade - arrow 1 -. Ensure joint sits completely in guide.
Lock wiper blade by slide on retaining clip - arrow 2 -.